Table 217.2 Wheelchair Accessible Telephones Number of Telephones Provided on a Floor, Level, or Exterior Site Minimum Number of Required Wheelchair Accessible...
Search Results "Clear Floor Area"
-
217.2 Wheelchair Accessible Telephones
-
Electronic instruments
Electronic instruments have been developed to measure floor flatness....
-
1009.2.1 Elevators required
In buildings where a required accessible floor is four or more stories above or below a level of exit discharge, at least one required accessible means of egress shall be an elevator complying...
-
1009.2.1 Elevators required
In buildings where a required accessible floor is four or more stories above or below a level of exit discharge, not less than one required accessible means of egress shall be an elevator...
-
§ 38.23(c)(5) Slope
If the height of the vehicle floor from which the ramp is deployed is 3 inches or less above a 6-inch curb, a maximum slope of 1:4 is permitted; if the height of the vehicle floor from which...
-
4.3.4 Knee and Toe Clearances
4.3.4 Knee and Toe Clearances Adequate space without an obstruction under a design element to the floor is essential for WhMD users to approach sufficiently close in a forward direction...
-
11B-809.1.2 Viewing devices
entry door to a residential dwelling units with mobility features shall also provide a lower viewing device 42 inches (1067 mm) minimum and 43 inches (1092 mm) maximum above the finish floor...
-
§ 36.404(b)
For example, alterations to floors above or below the accessible ground floor must be accessible regardless of whether the altered facility has an elevator....
-
Sec.36.404(b)
For example, alterations to floors above or below the accessible ground floor must be accessible regardless of whether the altered facility has an elevator....
-
Eliminating Hazards [4.26.4]
Extensions must be rounded or returned to the walls, floors, or posts. Extensions with bottom edges within 27 inches of the floor are detectable within the standard sweep of canes....
-
Door and Gate Hardware: ADA Standard Section 404.2.7
Section 404.2.7 covers the current ADA Standards for door and gate hardware.
-
Size: ADA Standard Section 604.8.1.1
Section 604.8.1.1 covers the current ADA Standards for the size of wheelchair accessible compartments.
-
Edge Protection: ADA Standard Section 1005.3
platform 12 inches (305 mm) where the 34 inch (865 mm) high railing is provided is an alternative design, permitting individuals using wheelchairs or other mobility devices to pull into a clear...
-
Panda TS.87 Thermally Broken Slim Profile Lift & Slide System
Glazing: Clear Low-E tempered 1 3/8″ insulated is the standard. A minimum of 1/4″ single pane glass to a maximum 1 1/2″ hurricane rated insulated glass may be used....
-
Panda TS.19 Thermally Broken Lift & Slide System
Glazing: Clear Low-E Insulated is the standard. Various types of glass and other materials at a thickness of up to 1 7/8″ may be used. Optional integrated blinds are available....
-
Section 6.0 Conclusions
Clear floor space: A large minority of participants in our research would not be accommodated by the current U.S. standard for clear floor space, especially for length....
-
Scoping [4.1.3(5)]
Under ADAAG, a floor must contain occupiable space in order to be considered a "story."...
-
Accessible Path of Travel
When alterations are made to a primary function area, an accessible path of travel to the area must be provided....
-
BEA Inc. LZR-Microscan Swinging Door Sensor
Time of Flight technology eliminates nuisance detections due to changing floor conditions. LZR-microscan is the only UL Listed swing door sensor on the market today! ...
-
11B-608.2.2 Standard roll-in type shower compartments
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
406.6 Diagonal Curb Ramps
The bottom of diagonal curb ramps shall have a clear space 48 inches (1220 mm) minimum outside active traffic lanes of the roadway....
-
11B-608.2.2 Standard roll-in type shower compartments
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
Suggested Styles and Conventions for Closed Captioning - by WGBH
Aim for a style that consistently conveys information in a clear, logical manner, using stylistic rules and conventions in a way that makes it easy for the viewer to understand and interpret...
