Transfer supports for transfer surfaces complying with M301.2.3.1 and M302.2 shall be located on the short side (length) opposite the transfer side....
Search Results "Assisted Transfer"
-
M305.2.1.1 End Transfer Supports
-
M305.2.2.2 Side Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.2 shall be 28 inches (710 mm) long minimum and shall be positioned along the width of transfer surfaces....
-
Minimum Number: ADA Standard Section 234.3
Section 234.3 covers scoping requirements in the current ADA Standards for the minimum number of wheelchair spaces required at amusement rides.
-
RECOMMENDED CHANGE
RECOMMENDED CHANGE Revise the Section 5.4.11 recommendation as follows: The Committee recommends transfer supports and connections contain the strength to resist vertical forces of...
-
Study Objectives
The purpose of this study was to examine independent transfers to and from a WMD and a simple platform, with and without the use of grab bars and/or a backrest, and transfers between two...
-
11B-1008.3.2.4 Contrasting stripe
Striping complying with Section 11B-504.4.1 shall be provided at each transfer step. FIGURE 11B-1008.3.2 TRANSFER STEPS...
-
Key Study findings:
wouldn’t attempt to transfer at all and 3 of which attempted the transfer but failed in the process). ...
-
D. Assisted Listening Devices:
By October 1, 2014, Olympia shall provide no less than forty-nine (49) fully functional receivers for assisted listening systems (“Assisted Listening Devices”) available for patrons...
-
Backrests
Backrests: The backrest design for platform 1, the first surface that participants transferred to from their WMD as seen in Table 2, was based on bench seat back supports in section 903.5...
-
M305.2.2 Structural Strength
Transfer supports and their connections shall be capable of resisting vertical and horizontal forces of 250 pounds (1,112 N) applied at all points on the transfer support....
-
M302.3.1 Transfer Supports (Section-by-Section Analysis)
In the MDE NPRM the Access Board proposed that transfer supports must be provided for use with transfer sides on diagnostic equipment used by patients in the seated position, and that these...
-
5.4.2.2 Transfer and Positioning Support Length for Imaging Equipment with Transfer Surfaces
5.4.2.2 Transfer and Positioning Support Length for Imaging Equipment with Transfer Surfaces....
-
5.3.2.2 Transfer Sides for Imaging Equipment
5.3.2.2 Transfer Sides for Imaging Equipment. The transfer surface should be provided on at least one long side of the table....
-
For More Information
For more information about the Americans with Disabilities Act (ADA), please visit the Department of Justice’s Home Page, http://www.ada.gov/index.html, or call us on the ADA...
-
Receiver Jacks: ADA Standard Section 706.2
Receivers required for use with an assistive listening system shall include a 1/8 inch (3.2 mm) standard mono jack....
-
11B-706.2 Receiver jacks
Receivers required for use with an assistive listening system shall include a 1/8 inch (3.2 mm) standard mono jack....
-
11B-706.2 Receiver jacks
Receivers required for use with an assistive listening system shall include a 1/8 inch (3.2 mm) standard mono jack....
-
How to Measure Transfer Surface Height
How to Measure Transfer Surface Height Regardless of the final decision on the low height measurement, the Subcommittee agreed that the height of the transfer surface would be measured...
-
11B-1002.6.3 Wheelchair storage space
Wheelchair storage spaces complying with Section 11B-305 shall be provided in or adjacent to unload areas for each required transfer device and shall not overlap any required means of egress...
-
11B-1002.6.3 Wheelchair storage space
Wheelchair storage spaces complying with Section 11B-305 shall be provided in or adjacent to unload areas for each required transfer device and shall not overlap any required means of egress...
-
11B-1002.6.3 Wheelchair storage space
Wheelchair storage spaces complying with Section 11B-305 shall be provided in or adjacent to unload areas for each required transfer device and shall not overlap any required means of egress...
-
11B-234.3 Minimum number
Amusement rides shall provide at least one wheelchair space complying with Section 11B-1002.4, or at least one amusement ride seat designed for transfer complying with Section 11B-1002.5...
-
11B-234.3 Minimum number
Amusement rides shall provide at least one wheelchair space complying with Section 11B-1002.4, or at least one amusement ride seat designed for transfer complying with Section 11B-1002.5...
-
1002.6.3 Wheelchair Storage Space
Wheelchair storage spaces complying with 305 shall be provided in or adjacent to unload areas for each required transfer device and shall not overlap any required means of egress or accessible...