By the end of 2006, NCA had initial commitments from a number of state or federal outdoor recreation entities to provide test sites for the trail surface study, however, the down turn in...
Search Results "Transfer Surface Height"
-
Modifications to the Longitudinal Study
-
11B-705.1.2.1 Platform edges
Detectable warning surfaces at platform boarding edges shall be 24 inches (610 mm) wide and shall extend the full length of the public use areas of the platform....
-
705.2 Platform Edges
Detectable warning surfaces at platform boarding edges shall be 24 inches (610 mm) wide and shall extend the full length of the public use areas of the platform....
-
R405.3.2 Maximum Depth
Knee clearance shall extend 635 mm (2.1 ft) maximum under an element at 230 mm (9 in) above the finish surface....
-
T402.8.2 Deployment to Boarding Platforms
The running slope of ramps and bridgeplates used for deployment to platforms shall be 1:8 maximum, as measured to the boarding platform with the non-rail vehicle resting on a flat surface...
-
A6
If a curb ramp is provided, is the running slope of the ramp surface (not counting the side flares) no more than 1:12 or 8.33% [ADA Standards § 4.7.2] Yes No...
-
M12
If a mirror is provided, is the bottom of the reflecting surface no higher than 40 inches above the floor or is a full length mirror provided?...
-
SECTION#2
SECTION#2 For the following questions, please answer every item pertaining to the trail surface composition....
-
Accessibility
Accessibility: When ceramic tile is used as the flooring surface, design professionals should consider the following, based on ANSI A108.01 and A108.02, where accessibility is a primary...
-
11B-705.1.2.1 Platform edges
Detectable warning surfaces at platform boarding edges shall be 24 inches (610 mm) wide and shall extend the full length of the public use areas of the platform....
-
705.2 Platform Edges
Detectable warning surfaces at platform boarding edges shall be 24 inches (610 mm) wide and shall extend the full length of the public use areas of the platform....
-
Tour-Mate
Should your institution have Tour-Mate create your content as a ‘work for hire’, all tour copyrights that would normally attach to Tour-Mate, would transfer to your institution upon completion...
-
Construction and Maintenance Practices
An accessible surface is firm and stable. Use caution with the size and depth of gravel when maintaining unpaved surfaces....
-
Soft Contained Play Structures
Transfer systems (left) or platform lifts can serve as a part of an accessible route connecting entry points on soft-contained play structures....
-
vii. Ancillary equipment
Sliding boards or sheets and gait belts may assist in transfers of patients with disabilities to and from examination or treatment tables and chairs....
-
Other Features in Progress
Moveable stairs for transfer into the spa from a wheelchair Grab bars around the roll-in shower in the den bath Fold-down blockers on all sliding doors for increased security...
-
Bathtub
For individuals who had the ability to ambulate, a walk-in fixture was intended to provide a safer alternative for independent as well as assisted transfers....
-
Preliminary Guidelines for SEWF Installation
Do not saturate surface with these lubricants. After compaction the thickness will be approximately 40 mm (1.6 in.). 3....
-
11B-904.4.2 Forward approach
A portion of the counter surface that is 36 inches (914 mm) long minimum and 34 inches (864 mm) high maximum shall be provided....
-
R402.3 Post-Mounted Objects
Where objects are mounted on free-standing posts or pylons and the objects are 685 mm (2.25 ft) minimum and 2030 mm (6.7 ft) maximum above the finish surface, the objects shall overhang...
-
A. Arena Assembly Seating:
The floor surface of the Companion Seat shall be at the same elevation as the floor surface of the Wheelchair Seat. ...
-
1.1.8 Alternate measurement tools
Although the F - number system can be used to measure surface flatness for smooth surfaces it requires expensive equipment and workers trained to do the measurement....
-
11B-603.3 Mirrors
Mirrors located above lavatories or countertops shall be installed with the bottom edge of the reflecting surface 40 inches (1016 mm) maximum above the finish floor or ground....
-
11B-812.8.7 Location
Signs shall be 60 inches (1525 mm) minimum above the finish floor or ground surface measured to the bottom of the sign....
