The surface of vehicle parking spurs shall be firm and stable. The type of surface should be appropriate to the setting and level of development....
Search Results "Transfer Surface"
Filters
Commonly Searched Documents
-
3.1.2 Surface of Vehicle Parking Spurs
-
5.3.2.2 Surface
The surface of the turning space and clear floor or ground space shall be firm and stable. ...
-
304.2 Floor or Ground Surfaces
304.2 Floor or Ground Surfaces. Floor or ground surfaces of a turning space shall comply with 302. Changes in level are not permitted....
-
4.7.4 Surface
The surface of the clear floor or ground spaces required by section 4.0 shall be firm and stable. The type of surface should be appropriate to the setting and level of development....
-
4.8.6 Cross Slope and Surfaces
The cross slope of ramp surfaces shall be no greater than 1:50. Ramp surfaces shall comply with 4.5....
-
4.8.6 CROSS SLOPE AND SURFACES
The cross slope of ramp surfaces shall be no greater than 1:50. Ramp surfaces shall comply with 4.5....
-
4.5.4 Surface
The surface of the clear floor or ground space for trash, recycling, and other essential containers shall be firm and stable....
-
304.2 Floor or Ground Surfaces
Floor or ground surfaces of a turning space shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
304.2 Floor or Ground Surfaces
Floor or ground surfaces of a turning space shall comply with 302. Changes in level are not permitted....
-
7.4.1 Surface
The trail tread surface, including resting intervals and passing spaces, shall be both firm and stable....
-
Figure 1009.5.1 Size of Transfer Platform – Drawing from the U.S. Access Board
-
4.3.4 Tent Pad or Platform Surface
Tent pads and platforms shall have a surface that is firm and stable and is designed to allow use of tent stakes and other tent securing devices. Exception. ...
-
5.4.1 Transfer Support Location for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.1 Transfer Support Location for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
Selection of Trail Surface Materials
Selection of Trail Surface Materials A review of trail surfacing products conducted for this project identified approximately 80 different trail surface materials that promoted providing...
-
5.4.2 Transfer Support Length for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.2 Transfer Support Length for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
11B-1002.5 Amusement ride seats designed for transfer
Ride seats designed for transfer should involve only one transfer....
-
11B-1002.5 Amusement ride seats designed for transfer
Ride seats designed for transfer should involve only one transfer....
-
11B-1002.5 Amusement ride seats designed for transfer
Ride seats designed for transfer should involve only one transfer....
-
R302.7.2 Vertical Surface Discontinuities
R302.7.2 Vertical Surface Discontinuities. Vertical surface discontinuities shall be 13 mm (0.5 in) maximum....
-
(3) Transfers of Privately Held Equity Interests
(3) Transfers of Privately Held Equity Interests: A transfer of interest in a Brand Hotel in which, after conveyance of the interest, a 25% or more cumulative interest in the Brand Hotel...
-
11B-226.2 Dispersion
Dining surfaces required to comply with Section 11B-902 shall be dispersed throughout the space or facility containing dining surfaces for each type of seating in a functional area....
-
5.3 Transfer Sides Recommendations
5.3 Transfer Sides Recommendations...
-
M305.2.1 Location (Section-by-Section Analysis)
For transfer surface depths on tables less than 24 inches wide, a transfer support must be available on the side opposite the entry of the transfer surface… For transfer surface depths on...
-
Surface discontinuities
Differences in level between two adjacent surfaces. Elevation changes due to ramps or stairs do not, themselves, constitute surface discontinuities....
