The clearance between the platform sill and the edge of any runway landing shall be 1¼ inch (32 mm) maximum....
Search Results "Curb Ramp Bottom Landing"
Filters
Commonly Searched Documents
-
11B-410.4 Platform to runway clearance
-
EZ-ACCESS GATEWAY™ Solid Surface Portable Ramp
The Gateway™ Solid Surface Portable Ramp – the 1-piece design means no assembly or moveable parts; just set the ramp in the desired position, and it’s ready to use....
-
1. Public Right-of-Way
construction, and accessibility conclusions of the curb ramps at issue....
-
Q15: Other Requirements Triggered by Road Resurfacing Alterations
Q15: In addition to the obligations triggered by road resurfacing alterations, are there other title II or Section 504 requirements that trigger the obligation to provide curb ramps? ...
-
4.1.6(1)(b)
requirements) requiring major structural changes are planned or installed where none existed previously, then a means of accessible vertical access shall be provided that complies with 4.7, Curb...
-
405.9.2 Curb or Barrier
405.9.2 Curb or Barrier....
-
R407.9.2 Curb or Barrier
R407.9.2 Curb or Barrier....
-
1.9.1.1.1
1.9.1.1.1 All buildings, structures, sidewalks, curbs and related facilities constructed in the state by the use of state, county or municipal funds, or the funds of any political subdivision...
-
405.9.2 Curb or Barrier
A curb or barrier shall be provided that prevents the passage of a 4 inch (100 mm) diameter sphere, where any portion of the sphere is within 4 inches (100 mm) of the finish floor or ground...
-
R304.5.3 Cross Slope
The cross slope of curb ramps, blended transitions, and turning spaces shall be 2 percent maximum....
-
Rise: ADA Standard Section 405.6
Section 405.6 covers the current ADA Standards for the rise requirements of ramps.
-
11B-405.6 Rise
The rise for any ramp run shall be 30 inches (762 mm) maximum....
-
405.9.2 Curb or Barrier
A curb or barrier shall be provided that prevents the passage of a 4 inch (100 mm) diameter sphere, where any portion of the sphere is within 4 inches (100 mm) of the finish floor or ground...
-
405.9.2 Curb or Barrier
A curb or barrier shall be provided that prevents the passage of a 4 inch (100 mm) diameter sphere, where any portion of the sphere is within 4 inches (100 mm) of the finish floor or ground...
-
Curbs [4.21.7]
Curbs [4.21.7] Curbs are not permitted at roll-in showers. A slope up to 2% is allowed for drainage....
-
1.9.1.1.4
1.9.1.1.4 With respect to buildings, structures, sidewalks, curbs and related facilities not requiring a building permit, building standards published in the California Building Standards...
-
B. Interior Ramps
Interior Ramps (1) Royal Street Entrance Interior Ramp - Defendants will rebuild this ramp so that it meets 2010 Standards §§ 206.2.4 and 405....
-
SECTION 1012 RAMPS
[DSA-AC] In addition to the requirements of this section, means of egress, which provide access to, or egress from, buildings or facilities where accessibility is required for...
-
Can curbs be used to indicate areas with less than 80” of vertical clearance?
Curbs may be mistaken for a step or change in level, instead of a barrier....
-
11B-303.5 Warning curbs
changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning curbs...
-
Accessible Ramp Features
Accessible Ramp Features 1. At least 36 inches between handrails 2. Top landing part of walk 3. Bottom landing part of walk 4. Handrail height 34 to 38 inches 5....
-
SafePath EZCurb™ Wheelchair Ramps - Vertical Barrier Removal
EZCurbTM Ramps are designed to provide ramped access and vertical barrier removal where there is a single path-of-travel requirement....
