Even dimensions that accommodate our entire sample might not accommodate someone who is larger or smaller than the people we measured....
Search Results "Absolute Dimension"
Filters
Commonly Searched Documents
-
4.2 Applications of Findings in Design and Standards Development
-
IDEA Center
This occurs mostly with dimensions near the hands and other body parts that may move slightly during data collection....
-
A4.22.3 Clear Floor Space
Figure 28 (section 4.16) provides minimum clear floor space dimensions for toilets in accessible “unisex” toilet rooms....
-
Appendix 3 - Comparison of US Standards to IDEA Center Research
Appendix 3 - Comparison of US Standards to IDEA Center Research Dimension U.S....
-
1133B.5.4.5
Intermediate and bottom landings at a change of direction in excess of 30 degrees shall have a dimension in the direction of ramp run of not less than 72 inches (1829 mm) to accommodate...
-
Section 5 References
“Revised Knee Clearance Depth and Footrest Clearance dimensions for sizing of mammography equipment.” Memorandum. April 23, 2013....
-
Seat width and depth
This dimension is within the range of seat depths allowed for transfer steps in play and pool areas and for proposed diagnostic equipment (14 to 17 inches). ...
-
Openings in Trail Surfaces
Place elongated openings more than a quarter of an inch wide with the long dimension perpendicular or diagonal to the primary direction of travel (figure 138)....
-
Structure Sensor 3D Depth Scanning Software for 3D Imaging and Printing
The magic of 3D depth sensing begins with the ability to capture fast, accurate, dimensions of objects and environments....
-
4.1 Introduction
To provide realistic guidance for designers, information on wheeled mobility dimensions should include occupied sizes as well as device size; both in percentile form, and also include accessories...
-
4. COMMON PATH OF TRAVEL ITEMS
area of alteration • Public telephones serving the area of alteration • Exterior or interior signs along the path of travel • Accessible route components • Walking surfaces dimensions...
-
Parallel Curb Ramps (R304.3) (Section-by-Section Analysis)
Where the turning space is constrained on two or more sides, the turning space must be 1.2 meters (4 feet) minimum by 1.5 meters (5 feet) minimum, with the 1.5 meters (5 feet) dimension...
-
T-turn Maneuvering Space
The Department has decided to delete the reference to the T-turn dimensions in the Guidelines for Requirement 4....
-
11B-505.6 Gripping surface
distance between horizontal projections and the bottom of the gripping surface shall be permitted to be reduced by 1/8 inch (3.2 mm) for each ½ inch (12.7 mm) of additional handrail perimeter dimension...
-
Omnia Industries Inc. Modern Narrow Backset Lever Lockset - Solid Brass No.64036
Modern Narrow Backset Lever Lockset - Solid Brass Dimensions: 8-1/4" Overall Finishes: US3, US26, US26D Notes: Shown in US26...
-
Omnia Industries Inc. Interior Modern Lever Latchset - Stainless Steel No.47
Interior Modern Lever Latchset - Stainless Steel Dimensions: 3" Projection x 5- 1/2 " Length, 11/16" Lever Diameter Finishes: US32D...
-
1. LEGAL ISSUES
"What is an acceptable ‘dimensional tolerance’ obviously will vary, depending in part upon the purpose for the standard and the technological capacity to closely adhere to the target dimensions...
-
505.6 Gripping Surface
distance between horizontal projections and the bottom of the gripping surface shall be permitted to be reduced by 1/8 inch (3.2 mm) for each 1/2 inch (13 mm) of additional handrail perimeter dimension...
-
Purpose of the project
revise the dimensional limits set in the ADA/ABA Accessibility Guidelines nor to set specific tolerances within the body of the Guidelines, but rather to assist industry in developing dimensioning...
-
11B-505.6 Gripping surface
distance between horizontal projections and the bottom of the gripping surface shall be permitted to be reduced by 1/8 inch (3.2 mm) for each ½ inch (12.7 mm) of additional handrail perimeter dimension...
-
Section 810.2.2
Section 810.2.2 The Department recognizes that there will be some situations in which the full dimensions of a bus boarding and alighting area complying with the §810.2.2 may not be able...
-
Reduced Contrast Sensitivity
If the letter’s absolutely black, there’s no light coming off of it, the contrast will be 100 percent, no matter what the background is, as long as it’s not black too....
-
Don-Jo Mfg., Inc. Door Viewers ULDV 180
Number ULDV 180 Dimensions 180 Degrees Ansi L23221 Shelf pack 10 Finishes 605, 626 Features...
-
Don-Jo Mfg., Inc. Door Viewers DV 180
Number DV 180 Dimensions 180 Degrees Ansi L21371 Shelf pack 10 Finishes 605, 626 Features...
