The floor or ground area within the required clearances shall be level and clear....
Search Results "Floor Designation"
-
4.13.6 Maneuvering Clearances at Doors
-
Side Approach
Recommendation: The clear floor space should be centered on the ATM unit....
-
Sales Counters [7.2(1)]
it is necessary to consider counters where only certain transactions can be made such as refunds for example, or counters that exclusively serve specific departments or areas of a sales floor...
-
Extensions
Handrails that are not continuous must have horizontal extensions at both the top and bottom of the ramp at least 12 inches long that are rounded or returned smoothly to walls, posts, or floors...
-
Vertical Wheelchair Lifts
The ASME code specifies a maximum travel distance of 12 feet and prohibits penetration of floors....
-
Scoping [4.1.3(21), 4.1.6(3)(h)]
In alterations, where this is not technically feasible, at least one accessible dressing room per floor is allowed for each sex (or one unisex room if that is the only type provided)....
-
4.1.6(4)(c)
(ii) Where existing shaft or structural elements prohibit strict compliance with 4.10.9, then the minimum floor area dimensions may be reduced by the minimum amount necessary, but in no...
-
5.2 FOOD SERVICE LINES
Tray slides shall be mounted no higher than 34 in (865 mm) above the floor. If self-service shelves are provided, a reasonable portion must be within the ranges shown in Fig. 53....
-
4.34.6.6* RANGES AND COOKTOPS
The clear floor space may overlap the knee space, if provided, by 19 in (485 mm) maximum. The location of controls for ranges and cook-tops shall not require reaching across burners....
-
1134A.8, Item 4.3
The clear floor space required by Item 2 shall not extend into the knee and toe space more than 19 inches (483 mm). (See Figure 11A-9D)....
-
Are closet doors and pantry doors required to comply?
cabinets and other storage elements not providing user passage do not have to comply with provisions for doors, but must meet requirements for storage (§811), including those for clear floor...
-
11B-604.9.5 Flush controls
Hand operated flush controls shall comply with Sections 11B-309.2 and 11B-309.4 and shall be installed 36 inches (914 mm) maximum above the finish floor....
-
Teknion Journal
Designed by Chris Wright and Steve Tsai, Journal is a comprehensive wood casegoods system with a refined modern aesthetic designed to address this need....
-
Accessible Route to Parking
The Board has added a requirement that spaces and access aisles be designed so that parked vehicles "cannot obstruct the required clear width of adjacent accessible routes" (502.7)....
-
INTRODUCTION
These changes include revised accessibility standards, called the 2010 Standards for Accessible Design (2010 Standards), which establish minimum criteria for accessibility in design and...
-
Are self-evaluations and transition plans required to be updated?
Although there is no requirement to update them, updating is the best means to ensure compliance with current regulations and design standards. A lot has changed in 27 years....
-
A. Accessibility Laws
. §§ 12101, et seq. and all of its implementing regulations and design standards; the Rehabilitation Act of 1973, 29 U.S.C. §§ 790, et seq. and all of its implementing regulations and design...
-
13. New Construction and Alterations
Construction and Alterations The City shall ensure that all new construction and alteration work at Pedestrian Facilities fully complies with the 2010 ADA Standards for Accessible Design...
-
11B-1009.2.4 Seat
The height of the lift seat shall be designed to allow a stop at 17 inches (432 mm) minimum to 19 inches (483 mm) maximum measured from the deck to the top of the seat surface when in the...
-
407.7 Color (Section-by-Section Analysis)
The use of color is also addressed in existing 508 Standards § 1194.22(c), which requires that Web pages “be designed so that all information conveyed with color is also available without...
-
Grab Bars [4.16.4]
Alternative designs, such as movable grab bars, were considered when ADAAG was developed but information and consensus was lacking on their usefulness and performance....
-
F244.2.1 Alterations and Additions
Where an entity is implementing a transition plan for program accessibility developed pursuant to regulations issued under section 504 of the Rehabilitation Act that designates specific...
-
Shape and Diameter
Large sections, particularly those of rectangular design, are not as graspable as smaller circular sections. A gripping surface width between 1¼ to 1½ inches diameter is specified....
-
F245.2.3 Alterations and Additions
Where an entity is implementing a transition plan for program accessibility developed pursuant to regulations issued under section 504 of the Rehabilitation Act that designates specific...