Trail classifications range from Trail Class 1 trails that appear little different from animal paths and may disappear intermittently, to Trail Class 5 trails that are usually wide, paved...
Search Results "Enhanced 9-1-1"
-
Trail Classes
-
410.5 Digital Encoding of Speech
ICT shall transmit and receive speech that is digitally encoded in the manner specified by ITU-T Recommendation G.722 (incorporated by reference in Chapter 1) for encoding and storing audio...
-
Questions to Consider
Questions to Consider: 1. What limitations does the employee with ASD experience? 2. How do these limitations affect the employee’s job performance? 3....
-
603.2.3 Door Swing
EXCEPTIONS: 1....
-
II. SPECIFIC ACTION TO BE TAKEN BY OLYMPIA:
For actions that have no specific deadline, Olympia shall complete them as soon as practicable but no later than prior to the commencement of the October 1, 2014-September 30, 2015 Entertainment...
-
§100.205(e)(2)(v) 2003 International Building Code (IBC)
Exception 1 to Section 1107.4 is not applicable to site arrival points for any Type B dwelling units because site impracticality is addressed under Section 1107.7.”...
-
III-4.1300 Unnecessary inquiries
ILLUSTRATION 1: A private summer camp requires parents to fill out a questionnaire and to submit medical documentation regarding their children's ability to participate in various camp activities...
-
1.1.7 Measurement of parking areas
These areas should be considered as a pedestrian walk with a minimum width of 60 in. and a length of approximately 20 ft and with an ADA/ABA - AG maximum slope of 1:48 in both directions...
-
Carpet [§302.2]
The standards specify the maximum pile height (1/2” measured to the backing, cushion, or pad) and texture (level or textured loop, level cut pile, or level cut/uncut pile) and require firm...
-
Curb Ramps
ramp is located where pedestrians must walk across the ramp, or where it is not protected by handrails or guardrails, it shall have flared sides; the maximum slope of the flare shall be 1:...
-
11B-707.3 Operable parts
Exceptions: 1. Drive-up only automatic teller machines and fare machines shall not be required to comply with Sections 11B-309.2 and 11B-309.3. 2....
-
11B-232.2.1.3 Substitute cells
required mobility features in substitute cells (cells other than those where alterations are originally planned), provided that each substitute cell meets the following conditions: 1....
-
Reassignment
employer does not have to place someone in a vacant position as a reasonable accommodation when another employee is entitled to the position under a uniformly-applied seniority system.[9]...
-
Bonded Bridle Path Installation
Prior to the date of installation, the overnight temperature was 9°C (48°F)....
-
Questionnaire Data
0.441 100.00% 4.32 11 0.68 0.457 100.00% 4.33 9...
-
FAQ: How do I enter a New Event in my Corada WorkSpace?
To enter a new event in your WorkSpace (once you are logged in): 1. Click on 'My WorkSpace' at the top of the home page - this will take you to your WorkSpace home page. 2....
-
Allegion Von Duprin 55 Series Cross Bar Exit Devices
Latch bolt height to finished floor 40 3/32" (1018mm) at center Crossbar projection — neutral 3 3/4" (95mm), depressed 2 3/8" (60mm) Crossbar length 42" (1067mm) Lock stile case 7 1/...
-
11B-213.3.1 Toilet compartments
When the July 1, 2015 Supplement to the 2013 CBC was issued, this scoping was increased, thereby exceeding the 2010 ADAS scoping at large multi-user toilet rooms....
-
Smooth Surface
This provision requires that parts creating joints in the smooth surface are to be within 1/16 inch of the same plane as the other....
-
§ 382.5 Individual with a disability
As used in this definition, the phrase: (a) Physical or mental impairment means: (1) any physiological disorder or condition, cosmetic disfigurement, or anatomical loss affecting one...
-
§382.3 Individual with a disability
As used in this definition, the phrase: (a) Physical or mental impairment means: (1) Any physiological disorder or condition, cosmetic disfigurement, or anatomical loss affecting one...
-
F104.1.1 Construction and Manufacturing Tolerances
For example, if this document requires "1½ inches," avoid specifying "1½ inches plus or minus X inches."...
-
Passing Spaces [1016.4]
When passing spaces and resting intervals overlap, the technical requirements for resting intervals apply and the slope of the surface must be no steeper than 1:48 (2 percent) in any direction...
-
M301.2.3 Transfer Sides
Obstructions shall not be vertically less than 1" (25 mm) nor be horizontally more than 3" (75 mm) from the edge of the patient support surface provide unobstructed access to the transfer...
