(2) Ramp surface. The ramp or bridge plate surface shall be continuous and slip resistant, shall not have protrusions from the surface greater than 1/4 inch high, shall have a clear...
Search Results "Railing"
Filters
Commonly Searched Documents
-
§ 38.125(c)(2) Ramp surface
-
§ 38.125(c)(4) Ramp barriers
(4) Ramp barriers. Each side of the ramp or bridge plate shall have barriers at least 2 inches high to prevent mobility aid wheels from slipping off.
-
§ 38.93(d)(1) Requirements
(1) Requirements. Cars operating in stations with high platforms, or mini-high platforms, shall be coordinated with the boarding platform design such that the horizontal gap between...
-
§ 38.95(c)(6)(i) Requirement
(i) Requirement. When in use for boarding or alighting, the ramp or bridge plate shall be attached to the vehicle, or otherwise prevented from moving such that it is not subject to...
-
§ 38.83(c)(2) Ramp surface
(2) Ramp surface. The ramp or bridge plate surface shall be continuous and slip resistant, shall not have protrusions from the surface greater then 1/4 inch, shall have a clear width...
-
§ 38.113(e) Signage
(e) Signage. The International Symbol of Accessibility shall be displayed on the exterior of all doors complying with this section unless all cars and doors are accessible and are...
-
§ 38.95(c)(8) Handrails
The handrails shall be capable of withstanding a force of 100 pounds concentrated at any point on the handrail without permanent deformation of the rail or its supporting structure....
-
§ 38.125(c)(8) Handrails
The handrails shall be capable of withstanding a force of 100 pounds concentrated at any point on the handrail without permanent deformation of the rail or its supporting structure....
-
§ 37.21(a)
(a) This part applies to the following entities, whether or not they receive Federal financial assistance from the Department of Transportation:
-
11B-206.4.4.1 Location
Exception: Entrances to key stations and existing intercity rail stations retrofitted in accordance with 49 CFR 37.49 or 49 CFR 37.51 shall not be required to comply with Section 11B-206.4.4.1...
-
T101.1 Purpose
These Non-Rail Vehicle Guidelines, which consist of Chapters 1 through 7, contain scoping and technical requirements for new, used or remanufactured non-rail vehicles to ensure their accessibility...
-
206.4.4.1 Location
EXCEPTION: Entrances to key stations and existing intercity rail stations retrofitted in accordance with 49 CFR 37.49 or 49 CFR 37.51 shall not be required to comply with 206.4.4.1....
-
206.4.4.1 Location
EXCEPTION: Entrances to key stations and existing intercity rail stations retrofitted in accordance with 49 CFR 37.49 or 49 CFR 37.51 shall not be required to comply with 206.4.4.1....
-
T505 Fare Collection Devices
[See subsections ...]
-
T602 Wheelchair Spaces
[See subsections ...]
-
T304 Operable Parts
[See subsections ...]
-
T505.3 Location of Operable Parts
Operable parts shall be located so that they are reachable by passengers using wheelchair when parked in a clear space 30 inches (760 mm) wide minimum and 48 inches (1220 mm) long...
-
7. In § 37.103 (b) and (c), remove the words “or an over-the-road bus,”
§ 37.103 [Amended] 7. In § 37.103 (b) and (c), remove the words “or an over-the-road bus,”.
-
T602 Wheelchair Spaces
The technical requirements for wheelchair spaces include provisions on surfaces, approach, and size. Under the final rule, as with the existing guidelines, one full unobstructed side...
-
§ 38.107(b)
(b) Restrooms required to be accessible shall be in close proximity to at least one seating location for persons using mobility aids and shall be connected to such a space by an...
-
§ 38.125(c)(3) Ramp threshold
(3) Ramp threshold. The transition from station platform to the ramp or bridge plate and the transition from car floor to the ramp or bridge plate may be vertical without edge...
-
§ 38.83(b)(8) Platform entrance ramp
(8) Platform entrance ramp. The entrance ramp, or loading-edge barrier used as a ramp, shall not exceed a slope of 1:8 measured on level ground, for a maximum rise of 3 inches, and...
-
§ 38.95(c)(2) Ramp surface
(2) Ramp surface. The ramp or bridge plate surface shall be continuous and slip resistant, shall not have protrusions from the surface greater than 1/4 inch high, shall have a clear...
-
§ 38.125(c)(6)(i) Requirement
(i) Requirement. When in use for boarding or alighting, the ramp or bridge plate shall be attached to the vehicle, or otherwise prevented from moving such that it is not subject to...