Hager Push/Pull Latch 311H: - New design replacing 311D - Engraving is available (optional) - Non-handed - Hospital latch Standard Materials: - Zinc and stainless...
Search Results "Pull Side"
-
Hager Companies Push/Pull Latch 311H
-
Hager Companies Round Offset Door Push/Pull Set 24Q
Round Offset Door Push/Pull Set 24Q Materials:- Aluminum, brass, bronze, stainless steel ...
-
609.4 Side Wall Grab Bar Height
-
Hager Companies Push/Pull Latch 311L
Hager Push/Pull Latch 311L: - Engraving available (optional) - Lead lined - Non-handed - Hospital Latch - 311L is same as 311H but for use on lead lined doors - *Horizontal...
-
404.2.4.3 Recessed Doors and Gates
Maneuvering clearances for forward approach shall be provided when any obstruction within 18 inches (455 mm) of the latch side of a doorway projects more than 8 inches (205 mm) beyond the...
-
404.2.4.3 Recessed Doors and Gates
Maneuvering clearances for forward approach shall be provided when any obstruction within 18 inches (455 mm) of the latch side of a doorway projects more than 8 inches (205 mm) beyond the...
-
TownSteel THPP Push and Pull Plate
TSPP Push and Pull is made from 16 gage stainless steel. Many different sizes to choose....
-
Jacknob Corp. 6251 3" High ADA Door Pull Brass-Chrome
6251 Door Pull 3" High (ADA) Brass/Chrome Polished Chrome Brass...
-
Medical Diagnostic Equipment Accessibility Standards Sub Committee Recommendations Stretcher Final Report
Specifically, Section M301, Diagnostic Equipment Used by Patients in Supine, Prone, or Side-Lying Position....
-
Rockwood Manufacturing Company 215 Tapered Door Pull 16"
Options: • Use Y prefix (Y215) when ordering pulls with base plates, Y plate diameter is 1-1⁄16"; recommended for use on glass or wood doors....
-
Rockwood Manufacturing Company 215L Tapered Door Pull 28"
Options: • Use Y prefix (Y215) when ordering pulls with base plates, Y plate diameter is 1-1⁄16"; recommended for use on glass or wood doors....
-
Rockwood Manufacturing Company 11047 Series 47 Straight Single Bar Set 8" Pull CTC
Metal: T4 Back to Back and Concealed; Pull Free End = 6, Push Free End = 6, Common End = 5....
-
Top Landing [§406.4]
Side flares, where provided, are intended primarily to prevent tripping hazards, not to accommodate wheelchair maneuvering at ramps (except in alterations where sufficient landing space...
-
5.6.1 Stirrups for Equipment Used by Patient in Supine, Prone, or Side-Lying Position
5.6.1 Stirrups for Equipment Used by Patient in Supine, Prone, or Side-Lying Position....
-
1132A.5.2 Strike edge maneuvering space at doors
The width of the level area on the side to which the door swings shall extend 18 inches (457 mm) past the strike edge for all doors....
-
1132A.5.2 Strike edge maneuvering space at doors
The width of the level area on the side to which the door swings shall extend 18 inches (457 mm) past the strike edge for all doors....
-
11B-404.2.7 Door and gate hardware
Handles, pulls, latches, locks, and other operable parts on doors and gates shall comply with Section 11B-309.4....
-
11B-404.2.7 Door and gate hardware
Handles, pulls, latches, locks, and other operable parts on doors and gates shall comply with Section 11B-309.4....
-
1012.1 General
Parking spaces within camping units and picnic units with mobility features and pull-up spaces for recreational vehicles at dump stations shall comply with 1012....
-
1012.1 General
Parking spaces within camping units and picnic units with mobility features and pull-up spaces for recreational vehicles at dump stations shall comply with 1012....
-
Lavatory and Accessory Layout by Terry Salo, Architect, CASp
Lavatory and Accessory Layout by Terry Salo, Architect, CASp NOTE: The trash receptacle is preferred to be near the door to allow people to pull the door open with a paper towel...
-
1132A.5.2 Strike edge maneuvering space at doors
The width of the level area on the side to which the door swings shall extend 18 inches (457 mm) past the strike edge for all doors....
-
503.4 Floor and Ground Surfaces
Vehicle pull-up spaces and access aisles serving them shall comply with 302. Access aisles shall be at the same level as the vehicle pull-up space they serve....
-
404.2.7 Door and Gate Hardware
Handles, pulls, latches, locks, and other operable parts on doors and gates shall comply with 309.4....
