This section requires the surface of beach access routes and resting intervals to be firm and stable....
Search Results "Floor Surface"
Filters
Commonly Searched Documents
-
1018.3 Surface
-
Handrails: ADA Standard Section 403.6
Section 403.5.4 covers the current ADA Standards for handrails that are provided along walking surfaces of accessible routes.
-
4.6.5 Slope
The slope of the clear floor or ground space required by section 4.6.4 shall not exceed 1:48 (2 percent) in any direction. Exception....
-
11B-403.6 Handrails
Where handrails are provided along walking surfaces with running slopes not steeper than 1:20 they shall comply with Section 11B-505. Advisory 11B-403.6 Handrails....
-
Elevator Car Requirements [§407.4.2 – §407.4.5]
Elevator Car Requirements [§407.4.2 – §407.4.5] Other requirements for elevator cars include: compliant floor surfaces a maximum 1¼” horizontal clearance between car...
-
1017.2 Surface
The surface of trails, passing spaces, and resting intervals shall be firm and stable. Advisory 1017.2 Surface. A firm trail surface resists deformation by indentations....
-
1017.2 Surface
The surface of trails, passing spaces, and resting intervals shall be firm and stable. Advisory 1017.2 Surface. A firm trail surface resists deformation by indentations....
-
Site Profiles by Surface Type
Some playground sites were surfaced with one surface material/system while others were surfaced with a combination of two surface materials/systems. ...
-
Exposed Pipes and Surfaces: ADA Standard Section 606.5
Section 606.5 covers the current ADA Standards for exposed pipes and surfaces under lavatories and sinks.
-
Suggested accessibility guidelines for exterior concrete surfaces
The following tolerances may be applicable for exterior accessible surfaces....
-
11B-1004.1 Clear floor space
Clear floor or ground spaces required at exercise machines and equipment shall be permitted to overlap. Advisory 11B-1004.1 Clear floor space....
-
403 Walking Surfaces
403 Walking Surfaces...
-
3.1.2 Surface of Vehicle Parking Spurs
The surface of vehicle parking spurs shall be firm and stable. The type of surface should be appropriate to the setting and level of development....
-
503.4 Floor and Ground Surfaces
503.4 Floor and Ground Surfaces. Vehicle pull-up spaces and access aisles serving them shall comply with 302....
-
Envirobond Organic-Lock™ Surface Stabilizer
Important features of a surface stabilized with Organic-Lock™ include: Erosion Control - Organic-Lock stabilized surfaces offer significantly improved resistance to erosion over...
-
11B-602.2 Clear floor space
Units shall have a clear floor or ground space complying with Section 11B-305 positioned for a forward approach and centered on the unit....
-
20. Does topping off a play surface trigger its replacement with an accessible surface?
Does topping off a play surface trigger its replacement with an accessible surface? No....
-
Height: ADA Standard Section 902.3
The tops of dining surfaces and work surfaces shall be 28 inches (710 mm) minimum and 34 inches (865 mm) maximum above the finish floor or ground....
-
11B-902.3 Height
The tops of dining surfaces and work surfaces shall be 28 inches (711 mm) minimum and 34 inches (864 mm) maximum above the finish floor or ground....
-
7.4.1 Surface
The trail tread surface, including resting intervals and passing spaces, shall be both firm and stable....
-
4.3.4 Tent Pad or Platform Surface
Tent pads and platforms shall have a surface that is firm and stable and is designed to allow use of tent stakes and other tent securing devices. Exception. ...
-
Selection of Trail Surface Materials
Selection of Trail Surface Materials A review of trail surfacing products conducted for this project identified approximately 80 different trail surface materials that promoted providing...
-
11B-611.2 Clear Floor Space
A clear floor or ground space complying with Section 11B-305 positioned for parallel approach shall be provided. The clear floor or ground space shall be centered on the appliance....
-
R302.7.2 Vertical Surface Discontinuities
R302.7.2 Vertical Surface Discontinuities. Vertical surface discontinuities shall be 13 mm (0.5 in) maximum....
