Hager Push/Pull Latch 311H: - New design replacing 311D - Engraving is available (optional) - Non-handed - Hospital latch Standard Materials: - Zinc and stainless...
Search Results "Door Pull"
Filters
Commonly Searched Documents
-
Hager Companies Push/Pull Latch 311H
-
2.2.6 Door Use
Trials in both directions were performed (i.e. from push and pull sides) using a forward approach. Each door presented different types of challenges to WhMD users....
-
Doors
[See subsections ...]
-
TownSteel THPP Push and Pull Plate
TSPP Push and Pull is made from 16 gage stainless steel. Many different sizes to choose....
-
2. Door Hardware
Is the bathroom door hardware (levers, pulls, etc.) easily operable with one hand, without tight grasping, pinching or twisting of the wrist, since many persons with disabilities may not...
-
11B-407.3 Elevator door requirements
Hoistway and car doors shall comply with Section 11B-407.3....
-
11B-407.3 Elevator door requirements
Hoistway and car doors shall comply with Section 11B-407.3....
-
11B-407.3 Elevator door requirements
Hoistway and car doors shall comply with Section 11B-407.3....
-
Revolving Doors or Turnstiles
A commenter advised that no revolving doors or turnstiles should be permitted on an accessible route. Response....
-
Vertical Clearance: ADA Standard Section 503.5
Section 503.5 covers the current ADA Standards for the vertical clearance at passenger loading zones.
-
Door and Gate Hardware
Section 404.2.7 also covers the operating characteristics and height of door and gate hardware....
-
11B-404.2.8.1 Door closers and gate closers
Door closers and gate closers shall be adjusted so that from an open position of 90 degrees, the time required to move the door to a position of 12 degrees from the latch is 5 seconds minimum...
-
11B-404.2.8.1 Door closers and gate closers
Door closers and gate closers shall be adjusted so that from an open position of 90 degrees, the time required to move the door to a position of 12 degrees from the latch is 5 seconds minimum...
-
11B-411.3.5 Width
The width of elevator doors shall comply with Table 11B-407.4.1....
-
Doors in a Series
A few commenters expressed concern that the Guidelines did not provide design for an entrance that consists of a series of more than one door....
-
11B-404.2.8.1 Door closers and gate closers
Door closers and gate closers shall be adjusted so that from an open position of 90 degrees, the time required to move the door to a position of 12 degrees from the latch is 5 seconds minimum...
-
Is compliance on both sides of a door or gate required when it is usable only from one side?
No, compliance is not required on both sides of those doors or gates that can be used in one direction only. Compliance is required only on the usable side....
-
11B-409.3 Elevator doors
Hoistway doors, car doors, and car gates shall comply with Sections 11B-409.3 and 11B-404....
-
11B-409.3 Elevator doors
Hoistway doors, car doors, and car gates shall comply with Sections 11B-409.3 and 11B-404....
-
11B-409.3 Elevator doors
Hoistway doors, car doors, and car gates shall comply with Sections 11B-409.3 and 11B-404....
-
Rockwood Manufacturing Company 102 x 70B - Pull Plate 5-1/2" CTC Pull 3-1/2" x 15" Plate
Material: Aluminum, Brass, Bronze, Stainless Steel Fastener: #6 x 5/8 OHSMS; 1/4 -20 x 2-1/4 Thru Bolt & Finish Washer (standard 1-3⁄4" door)....
-
1010.1.6 Thresholds
or landing for other doors....
-
Doors and Gates in Series [§404.2.6]
Doors and Gates in Series [§404.2.6] At hinged or pivoted doors or gates in series, a separation is required that is at least 48” plus the width of doors or gates swinging into the space...
-
4.1.3(7) Doors
(7) Doors:...
