Handrails provided along walking surfaces complying with 403, required at ramps complying with 405, and required at stairs complying with 504 shall comply with 505....
Search Results "Curb Ramp Surface"
Filters
Commonly Searched Documents
-
505.1 General
-
Floor Surfaces: ADA Standard Section 407.4.2
Section 407.4.2 covers the current ADA Standards for the floor surfaces of elevator cars.
-
Rise: ADA Standard Section 405.6
Section 405.6 covers the current ADA Standards for the rise requirements of ramps.
-
11B-405.6 Rise
The rise for any ramp run shall be 30 inches (762 mm) maximum....
-
11B-405.7.2 Width
The landing clear width shall be at least as wide as the widest ramp run leading to the landing....
-
Extended Ground or Deck Surface: ADA Standard Section 1005.3.2
The ground or deck surface shall extend 12 inches (305 mm) minimum beyond the inside face of the railing....
-
Curbs [4.21.7]
Curbs [4.21.7] Curbs are not permitted at roll-in showers. A slope up to 2% is allowed for drainage....
-
1.9.1.1.4
1.9.1.1.4 With respect to buildings, structures, sidewalks, curbs and related facilities not requiring a building permit, building standards published in the California Building Standards...
-
§ 38.23(c)(8) Handrails
grasp them from outside the vehicle while starting to board, and to continue to use them throughout the boarding process, and shall have the top between 30 inches and 38 inches above the ramp...
-
1.1.12 Ramp cross slope
1.1.12 Ramp cross slope....
-
R407.9.1 Extended Ramp Surface
R407.9.1 Extended Ramp Surface. The surface of the ramp run or landing shall extend 305 mm (1.0 ft) minimum beyond the inside face of a handrail complying with R409....
-
11B-505.2 Where required
Handrails shall be provided on both sides of stairs and ramps....
-
11B-505.10.1 Top and bottom extension at ramps
Ramp handrails shall extend horizontally above the landing for 12 inches (305 mm) minimum beyond the top and bottom of ramp runs....
-
Non-Circular Cross Sections: ADA Standard Section 505.7.2
Section 505.7.2 covers the current ADA Standards for the non-circular cross section of handrail gripping surfaces.
-
11B-505.7.2 Non-circular cross sections
Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches (102 mm) minimum and 6¼ inches (159 mm) maximum, and a cross-section dimension of...
-
1.2.3 Landings
Both measurements of ramp landings as described in Section 1.1.15 should not exceed a plus tolerance of 0.5%....
-
SECTION 1012 RAMPS
[DSA-AC] In addition to the requirements of this section, means of egress, which provide access to, or egress from, buildings or facilities where accessibility is required for...
-
Can curbs be used to indicate areas with less than 80” of vertical clearance?
Curbs may be mistaken for a step or change in level, instead of a barrier....
-
405 Ramps
Section 405 provides technical criteria for ramps....
-
Bosch Five-Point Self-Leveling Alignment Laser GPL 5 S
Description The GPL 5S is a five-point laser that levels, plumbs up, plumbs down, and squares. It accurately transfers and aligns level, plumb and 90 degree square points. With...
-
Bosch 3-Point Self-Leveling Alignment Laser GPL 3
Description Three-point plumb and level point projection laser accurately transfers and aligns plumb up/down, front level and align points; accuracy is +/- 1/4 In. at 100 ft....
-
Bosch 3 Point Self Leveling Alignment Laser Level GPL 3 S
Description The GPL3 offers limitless uses, everything from plumbing up floors and ceilings to installing drywall partitions and establishing benchmarks. And because it can be...
