Recognized tolerances are not intended to apply to design work. It is good practice when specifying dimensions to avoid specifying a tolerance where dimensions are absolute....
Search Results "Work Surface"
-
11B-104.1.1 Construction and manufacturing tolerances
-
Program requirements. (Section-by-Section Analysis)
include programs to obtain GEDs, computer training, job skill training and on-the-job training, religious instruction and guidance, alcohol and substance abuse groups, anger management, work...
-
Section 37.43 Alteration of Transportation Facilities by Public Entities
Finally, the Department has defined the term “begin”, in the context of begin an alteration that is subject to the alteration provision to mean when a notice to proceed or work order is...
-
IV. RESOLVING ADA COMPLAINTS THROUGH MEDIATION
The motel also agreed to work with the regional corporate office to increase awareness of all franchise motel owners about the ADA's requirements relating to service animals....
-
More Than Just a Pipe: Choosing Quality Glass for an Elevated Experience
A classic downstem diffuser breaks the smoke into bubbles, increasing the surface area that touches the water....
-
Wikk Industries Inc. Bollard With Push Plate Part #BPRT1435CSFT32D (630)
Formed 304 Satin Stainless Steel US32D (630), Removable bollard for surface mount with concealed sleeve (CS) with 7” bolts for mounting, 1 Prep for ADA switch, Welded flat top...
-
Bradley Stainless Steel Towel Hook 9314, 9315
Bradley Stainless Steel Towel Hook Model 9314, 9315 Surface-Mounted - Concealed Mounting Stainless Steel Vandal-Resistant Escutcheons Model 9134/9135: Satin...
-
Feature 1 - Parking and Passenger Drop-Off Areas
In order to be usable, the access aisle must be level, clear of gravel or mud, and the surface must be in good condition without wide cracks or broken pavement....
-
Vanity Counter Tops
The Board has removed the minimum surface requirement (2 square feet) for vanity counter tops....
-
Curb Ramps at Marked Crossings and Vehicular Lanes
width of the curb ramp (exclusive of flared sides) and shall extend either the full depth of the curb ramp or 24 inches (610 mm) deep minimum measured from the back of the curb on the ramp surface...
-
Benches
If benches are located in wet areas, the surface must be slip-resistant and designed not to accumulate water....
-
3. Buttock-Popliteal Length
The median buttock-popliteal length provides an upper bound for the depth of a seating surface....
-
3.3 Data Sources
Early on, it became clear that some Committee members were unfamiliar with issues raised during transfers from a wheelchair or scooter onto a surface such as an examination table....
-
4.3.3 Imaging Equipment Used for Interventional and Biopsy Procedures with Sedated Patients
patients undergoing these procedures receive some form of sedation prior to transfer.CC When sedated, all patients – regardless of their physical abilities – are assisted onto the transfer surface...
-
Beach Access Routes
A beach access route is a continuous, unobstructed path that crosses the surface of the beach and provides pedestrians access to the water....
-
Front grab bar protocol
The preferred grab bar height was measured between the floor and the top of the grab bar surface. ...
-
Edge Protection [4.8.7]
A rail mounted close enough to the ramp surface to prevent passage of a 4 inch diameter sphere can function like a curb in keeping front casters from getting stuck on vertical posts and...
-
BEA Inc. Jamb Style Door Access PTE (Push To Exit)
Available in hard wired and wireless options (433, 390 or 300 MHz) Beveled edges provide a tamper / vandal resistant solution Activation across the entire surface...
-
Landscape Forms Inc. Gretchen Bench
Freestanding, or surface mounted styles offered. Available in a variety of woods or PolySite™ recycled timbers (PolySite not offered in 96" length)....
-
Pilot Rock Omega Bike Rack
INSTALLATION: Surface mount installation. Requires six 3/8” dia. anchor bolts (not included)....
-
American Safety Tread Co., Inc. Stair Nosing Style 950
Surface Design: Cross Hatched Non-Slip cast metal stair nosing with #24 virgin grain Silicon Carbide abrasive granules embedded into the walking surface while the matrix is in a molten...
-
American Safety Tread Co., Inc. Stair Nosing Style 850
Surface Design: Cross Hatched Non-Slip cast metal stair nosing with #24 virgin grain Silicon Carbide abrasive granules embedded into the walking surface while the matrix is in a molten...
-
HEWI System Lignum Handrails
The warm surface of the wood and the round profile enable comfortable and secure gripping....
-
PDQ 4200 Series Exit Device Door Hardware
The American Eagle 4200 Series is a rim or surface vertical rod exit device....
