This is consistent with ANSI/AAMI HE 75 which recommends that the “support surface needs to be adjustable or have adjustable features (e.g., for the head, neck, back, lumbar region, leg,...
Search Results "Ground Surface"
-
M301.3.3 Head and Back Support
-
604.7 Dispensers
paper dispensers are installed above the side wall grab bar, the outlet of the toilet paper dispenser must be 48 inches (1220 mm) maximum above the finish floor and the top of the gripping surface...
-
B) Accessible Route
be at least 36 inches wide, have no abrupt vertical changes in level (such as a step), have a running slope no more than 1:12 in most cases, and meet other requirements for cross slope, surface...
-
Parking Spaces [4.6.3]
A maximum slope of 2% is required in all directions for both the space and access aisle since level surfaces are important for wheelchair transfer to and from vehicles....
-
Location [§208.3]
Locating accessible spaces required for a parking structure in a surface lot often will not qualify for this exception because such a location typically offers less convenience, security...
-
Slope [§405.2] and Cross Slope [§405.3]
will accommodate most irregularities or variances due to construction methods or materials according to a study sponsored by the Board (“Dimensional Tolerances in Construction and for Surface...
-
Some existing measurement protocols
Some existing measurement protocols Currently there are no generally accepted measurement protocols for determining the slope, flatness, or waviness of floor surfaces in terms of accessibility...
-
Changes in Level at Entry to Wheelchair Spaces (M303.3)
with drop offs ½ inch or greater would be required to provide edge protection 2 inches high minimum on each side to prevent users from inadvertently travelling off the sides of the ramped surface...
-
11B-704.4.1 Height
When in use, the touch surface of TTY keypads shall be 34 inches (864 mm) minimum above the finish floor....
-
11B-704.4.1 Height
When in use, the touch surface of TTY keypads shall be 34 inches (864 mm) minimum above the finish floor....
-
1133A.2 Clear floor space
A clear floor space at least 30 inches (762 mm) by 48 inches (1219 mm) that allows either a parallel or a forward approach shall be provided at the work surface required by Section 1133A...
-
Pressalit Care VALUE Support Arm Height Adjustable
Incl. fixing kit for brick wall Basic material: Steel Surface material: Rilsan End cap: Nylon (PA) Provides firm support when you are sitting, standing, or transferring to and...
-
Bradley High Capacity Towel Dispenser / 4.9 Gallon Waste Receptacle 2017
towels 4.9 gallon waste capacity Model 2017 - Recessed - BradEX Model 2017-10 - Semi-recessed (recesses 3-1/2"; projects 2-1/2") BradEX Model 2017-11 - Surface...
-
Bradley 12 Gallon Waste Receptacle
-10, 346-11 Satin finish stainless steel Model 346: Recessed (projects 2-3/4") Model 346-10: Semi-recessed (recesses 4", projects 4-3/4") Model 346-11: Surface-mounted...
-
Alterations to Existing Facilities
For example, if an alteration project involves only installing pedestrian signals at existing intersections and there are no detectable warning surfaces on the curb ramps at the intersections...
-
1003.3.2 Boarding Pier Clearances
At high water, the entire chain is floating and a transition plate connects the first float to the surface of the launch ramp....
-
Slopes and Resting Intervals for Beach Access Routes
When the surface is paved or is built with boards, the cross slope is not allowed to be steeper than 1:48 (2 percent)....
-
11B-1003.3.2 Boarding pier clearances
At high water, the entire chain is floating and a transition plate connects the first float to the surface of the launch ramp....
-
1.3.1 Overview of NPRM
Types of Equipment to Which Technical Criteria Applies Diagnostic Equipment Used by Patients in Supine, Prone, or Side-Lying Position (M301) Transfer surface...
-
A MINIMUM HIGHEST POINT STANDARD OF 19 INCHES IS CONSISTENT WITH EXISTING ACCESSIBILITY STANDARDS
A MINIMUM HIGHEST POINT STANDARD OF 19 INCHES IS CONSISTENT WITH EXISTING ACCESSIBILITY STANDARDS Current accessibility standards and regulations generally consider a transfer surface...
-
Bradley 2-Station Express Lavatory System SS-2N
, ANSI, UFAS and TAS compliant Serves 1 - 2 users at a time Standard lavatory spacing on 30" centers Continuous bowl is constructed of vandal-resistant Terreon or TerreonRE Solid Surface...
-
Bradley 3-Station Express Lavatory System SS-3N
, ANSI, UFAS and TAS Compliant Serves 1 - 3 users at a time Standard lavatory spacing on 30" centers Continuous bowl is constructed of vandal-resistant Terreon or TerreonRE Solid Surface...
-
Pilot Rock Bench B110C with Full-length Grab Bar
SPECIFICATIONS: FRAME: All welded steel frame fabrication: seat/back support channel is die-formed from 1/8" thick (11 ga.) steel, frame post and portable/surface mount foot are made using...
-
Inpro Corporation ENDURANT® Trench Drain Receptor
Features & Benefits: Manufactured with BioPrism® Solid Surface, an industry leading bioresin blend which has 13% biocontent BioPrism® Solid Surface is antimicrobial...
