Where individual outdoor constructed features are altered and the ground surface is not altered, the clear ground space shall not be required to comply with 1011.2.2 and 1011.2.3. 2. ...
Search Results "Curb Ramp Surface"
-
1011.2 Clear Ground Space
-
Start of Play Areas
It must have a slope no steeper than 1:48 so that people using wheelchairs or mobility devices do not have to hit the ball while positioned on a sloped surface....
-
Accessible Routes
The accessible route must comply with ADAAG provisions for location, width (minimum of 36 inches), passing space, head room, surface, slope (maximum of 1:12 or 8.33%), changes in level,...
-
11B-1009.5.2 Transfer space
A transfer space of 60 inches (1524 mm) minimum by 60 inches (1524 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer platform surface and shall...
-
10.3.1(13)
(13) Where it is necessary to cross tracks to reach boarding platforms, the route surface shall be level and flush with the rail top at the outer edge and between rails, except for a maximum...
-
1012.1 General
address the width of parking spaces and pull-up spaces for recreational vehicles (1012.2); the width of parking spaces for vehicles, other than recreational vehicles (1012.3); and the surface...
-
Alterations and Additions
Normal maintenance, such as pothole repair, surface patching, or repainting in place existing striping for a few spaces, is not considered an alteration except where it affects a facility...
-
§ 37.91(e)
Appropriate auxiliary aids and services include providing a hard surface on which to eat....
-
11B-1009.5.4 Transfer steps
The surface of the bottom tread shall extend to a water depth of 18 inches (457 mm) minimum below the stationary water level. [2010 ADAS] Advisory 1009.5.4 Transfer Steps....
-
11B-1009.5.4 Transfer steps
The surface of the bottom tread shall extend to a water depth of 18 inches (457 mm) minimum below the stationary water level. Advisory 11B-1009.5.4 Transfer steps....
-
1005.2.1 Height
At least 25 percent of the railings, guards, or handrails shall be 34 inches (865 mm) maximum above the ground or deck surface....
-
F105.2.2 ASME
standard includes additional provisions for runway enclosures, electrical equipment and wiring, structural support, headroom clearance (which is 80 inches minimum), lower level access ramps...
-
A. Whether Sidewalks Are a Service Program, or Activity Covered by Title II of the ADA and Section 564 of the Rehabilitation Act
enacted an ordinance holding landowners responsible for adjacent sidewalks, the city had authority over its sidewalks such that it was required to draft a transition plan pertaining to curb...
-
18. Inspections
year of the Compliance Period, class counsel in the Carter/Fahmie Action shall be entitled to participate in the meetings, inspections and monitoring discussed herein, as they relate to curb...
-
Expert opinion on current literature
There is a consensus among studies that transferring to a higher surface implies greater exertion of the upper limb (3-6) . ...
-
Taking Measurements
Taking Measurements Sloped Surfaces One way to measure slope is to use a 24-inch level with leveling bubble and a tape measure....
-
What was measured and why?
Often, an unstable surface, for example, may be perceived as very difficult because of the unstable footing, even though the individual does not have to exert him/herself....
-
1009.5.4 Transfer Steps
The surface of the bottom tread shall extend to a water depth of 18 inches (455 mm) minimum below the stationary water level. Advisory 1009.5.4 Transfer Steps....
-
Tread Obstacles on Beach Access Routes
When the surface of the beach access route is paved or is built with boards, tread obstacles must not be more than a half of an inch (13 millimeters) high....
-
1018.5 Obstacles
Where the surface is other than concrete, asphalt, or boards, obstacles are permitted to not exceed 1 inch in height measured vertically to the highest point....
-
R308.1 Transit Stops
Transit stops should be located so that there is a level and stable surface for boarding vehicles....
-
Instrumentation for Analysis
Appendix C) was created to collect data on the 11 trail segments including Rotational Penetrometer readings, inspection location in feet from trailhead, ruts, tread obstacles, or other surface...
-
11B-812.7.2 Marking
The color of the borderlines, hatched lines, and letters shall contrast with that of the surface of the access aisle....
-
1018.2 Aisles in assembly spaces
for applications listed in Section 1.9.1 regulated by the Division of the State Architect-Access Compliance, shall also comply with Chapter 11A or Chapter 11B, Section 11B-403 _|Walking Surfaces...