Elevator car doors or gates shall be positioned at the narrow end of the clear floor spaces required by Section 11B-409.4.1....
Search Results "Floor Surface"
-
11B-409.3.2 Location
-
1005 Fishing Piers and Platforms
Specifications for fishing piers and platforms address accessible routes, railings, edge protection, clear floor space, and turning space....
-
1134A.7, Item 3
The minimum height of water closet seats shall be 15 inches (381 mm) above the floor....
-
602.4 Spout Height
Spout outlets shall be 36 inches (915 mm) maximum above the finish floor or ground....
-
409.3.2 Location
Elevator car doors or gates shall be positioned at the narrow end of the clear floor spaces required by 409.4.1....
-
305.4 Knee and Toe Clearance
Unless otherwise specified, clear floor or ground space shall be permitted to include knee and toe clearance complying with 306....
-
4.18.2 Height
Urinals shall be stall-type or wall-hung with an elongated rim at a maximum of 17 in (430 mm) above the finish floor....
-
5f.
Is the elevator equipped with audible tones or bells or verbal annunciators that announce each floor as it is passed? [ADA Stds 4.10.13]...
-
11B-409.3.2 Location
Elevator car doors or gates shall be positioned at the narrow end of the clear floor spaces required by Section 11B-409.4.1....
-
1134A.7, Item 3
The minimum height of water closet seats shall be 15 inches (381 mm) above the floor....
-
11B-409.3.2 Location
Elevator car doors or gates shall be positioned at the narrow end of the clear floor spaces required by Section 11B-409.4.1....
-
11B-809.9.5 Lower shelving
Lower shelving and/or drawer space shall be provided at a height of 48 inches (1219 mm) maximum above the finish floor....
-
11B-809.10.8.3 Cabinets
The finished floor shall extend to the wall under the lavatory....
-
11B-708.4 Residential dwelling unit communication systems
Communications systems between a residential dwelling unit and a site, building, or floor entrance shall comply with Section 11B-708.4....
-
Inpro Corporation ENDURANT® Ceiling Hung Partitions
Our celling Hung privacy partitions are manufactured from BioPrism® Solid Surface featuring an industry leading bio-resin blend....
-
Reach Ranges and Operability Requirements
That is why there are different height and clear floor space requirements for forward and side reaches....
-
1002.5.2 Transfer Height
The height of amusement ride seats designed for transfer shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the surface of the load and unload area....
-
Note
As shown, there are several ways for grab bars to be designed with adequate gripping surfaces, while ensuring that nothing can be tied onto them....
-
Grab Bar Height
The Board has clarified that the height of grab bars is measured to the top of the gripping surface (609.4)....
-
R305.2.7 Boarding and Alighting Areas
At boarding and alighting areas at sidewalk or street level transit stops for rail vehicles, detectable warning surfaces shall be placed at the side of the boarding and alighting area facing...
-
SECTION#5
SECTION#5 For the following questions, please answer every item pertaining to the trail surface installation. Leave blank if the response choice is not applicable to you....
-
Can guards or collars be attached to handrails to prevent skateboard traffic?
No, handrail gripping surfaces at egress stairs subject to the Standards must be unobstructed on the top and sides and free of sharp or abrasive elements so that users can maintain a continuous...
-
68.10(20) Pedestrian Elements
(20) Pedestrian Elements--Components that make up a pedestrian access route including, but not limited to walking surfaces, ramps, curb ramps, crosswalks, pedestrian overpasses and underpasses...
-
Expert Report of Douglas J. Anderson, RAS, CASP, LCM Architects (August 8, 2018)
pedestrian route from the entrance to the voting area contains a suggestion box that protrudes more than 4 inches into the route and the bottom of the object is more than 27 inches above the floor...
