If Cinemark does not receive a response to its request at the end of the thirty day period, or at the end the sixty (60) day period if an extension is timely requested by the Department...
Search Results "End Transfer Surface"
-
6.9
-
402.1 General (Section-by-Section Analysis)
This provision is needed because, when ICT has closed functionality, the end user typically does not have the option of installing or attaching assistive technology....
-
The Target Population
For many dimensions women represent the smaller end of the distribution....
-
Text Telephones (TTYs) (Advisory Guidance)
If you are calling a combination TTY and voice number, tap the space bar several times to help the person on the other end identify this as a TTY call. e....
-
1005.2.1 Height
At least 25 percent of the railings, guards, or handrails shall be 34 inches (865 mm) maximum above the ground or deck surface....
-
403.5.1 Clear Width
Except as provided in 403.5.2 and 403.5.3, the clear width of walking surfaces shall be 36 inches (915 mm) minimum....
-
1005.2.1 Height
At least 25 percent of the railings, guards, or handrails shall be 34 inches (865 mm) maximum above the ground or deck surface....
-
R406.3 Unobstructed Side Reach
approach to an element and the side reach is unobstructed, the high side reach shall be 1220 mm (4.0 ft) maximum and the low side reach shall be 380 mm (1.25 ft) minimum above the finish surface...
-
Built-up Curb Ramps [4.7.6]
(The surface of access aisles cannot slope more than 2% in any direction)....
-
4.1.7(3)(e)
., open books), should be no higher than 44 in (1120 mm) above the floor surface....
-
4.7.1 General
In alterations, where a condition for exception in section 1.1 prohibits full compliance with a specific requirement for clear floor or ground space surface, slope, size, or location, the...
-
Wheelchair Work Measurement Method
Wheelchair work per meter values for straight and turning were determined for all test course surfaces except sand, under dry conditions using the Wheelchair Work Measurement Method in accordance...
-
Fixed tactile maps
Placement on a horizontal or near horizontal surface provides the map reader with a real world orientation....
-
6.9 Tread Obstacles
Where the surface is paved or is elevated above the natural ground, obstacles shall not exceed 1/2 inch (13 mm) in height measured vertically to the highest point....
-
Original research for ANSI A117.1 (1957 - 1961)
Buildings and Facilities Accessible to, and Usable by, the Physically Handicapped, ramps were assessed for flatness based on measuring 18 - inch increments on both edges of the ramped surface...
-
11B-704.5 TTY shelf
The telephone handset shall be capable of being placed flush on the surface of the shelf....
-
Common Requirements (R304.5) (Section-by-Section Analysis)
Grade breaks are not permitted on the surface of ramp runs and turning spaces. Surface slopes that meet at grade breaks must be flush....
-
Clearance in Base (M301.4.1 and M302.4.1)
would require the clearance in the base to be 44 inches wide minimum, 6 inches high minimum measured from the floor, and 36 inches deep minimum measured from the edge of the examination surface...
- Greenfields Outdoor Fitness Accessible Hand Cycle HP2009-7-21
- SDC Sure Exit® PSB560 REX Pressure Sense Exit Bar
- Baldwin Hardware Atlanta Escutcheon Entrance Set Door Hardware
- HEWI Range 170 Door Hardware
- NABCO GT1400 / Automatic Standard Folding Door
-
D. Department of Justice Activities Related to Health Care Providers and Medical Equipment
includes information on accessible examination rooms and the clear floor space needed adjacent to medical equipment for individuals who use mobility devices to approach the equipment for transfer...