The floor or ground surface of wheelchair spaces shall comply with Section 11B-302. Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted....
Search Results "Trail Surface"
-
11B-802.1.1 Floor or ground surface
-
11B-902.1 General
Dining surfaces and work surfaces shall comply with Sections 11B-902.2 and 11B-902.3....
-
11B-902.1 General
Dining surfaces and work surfaces shall comply with Sections 11B-902.2 and 11B-902.3....
-
11B-302 FLOOR OR GROUND SURFACES
[See subsections ...]
-
Common Questions (Floor and Ground Surfaces)
Common Questions
-
11B-302 Floor or ground surfaces.
[See subsections ...]
-
11B-302 Floor or ground surfaces
[See subsections ...]
-
Stability or Stable Surface
Stability or Stable Surface. ...
-
Performance for Surface Firmness and Stability
Performance for Surface Firmness and Stability In addition to the visual inspection and calculation of the surface deficiency score, the firmness and stability of the surfaces were measured...
-
13. Do the provisions for openings in floor and ground surfaces in Section 302.3 apply to walking surfaces in play areas?
Do the provisions for openings in floor and ground surfaces in Section 302.3 apply to walking surfaces in play areas? Yes....
-
Vertical Surface Discontinuities
Vertical Surface Discontinuities. Vertical differences in level between two adjacent surfaces....
-
407.4.2 Floor Surfaces
407.4.2 Floor Surfaces. Floor surfaces in elevator cars shall comply with 302 and 303....
-
404.2.4.4 Floor or Ground Surface
Floor or ground surface within required maneuvering clearances shall comply with 302. Changes in level are not permitted. EXCEPTIONS: 1....
-
404.2.4.4 Floor or Ground Surface
Floor or ground surface within required maneuvering clearances shall comply with 302. Changes in level are not permitted. EXCEPTIONS: 1....
-
Cross Slope and Surfaces [4.8.6]
Ramp surfaces must comply with requirements for ground and floor surfaces and be "stable, firm, and slip-resistant." A specific level of slip-resistance is not mandated....
-
11B-809.9.4 Work surfaces
Work surfaces shall be 36 inches (914 mm) maximum above the finish floor with minimum lengths at the following locations as required by this section: Linear length of 30 inches...
-
11B-809.9.4 Work surfaces
Work surfaces shall be 36 inches (914 mm) maximum above the finish floor with minimum lengths at the following locations as required by this section: Linear length of 30 inches...
-
1017.8.4 Turning Space
Where resting intervals are provided adjacent to the trail tread, a turning space complying with 304.3.2 shall be provided. ...
-
1017.8.4 Turning Space
Where resting intervals are provided adjacent to the trail tread, a turning space complying with 304.3.2 shall be provided....
-
5.2.1.2 Transfer Surface Depth Recommendation for M301
5.2.1.2 Transfer Surface Depth Recommendation for M301 The Committee recommends a minimum transfer surface depth of 17 inches for all M301 except imaging equipment....
-
KICK PLATE
An abrasion-resistant plate affixed to the bottom portion of a door to prevent a trap condition and protect its surface. Advisory Definition of KICK PLATE....
-
KICK PLATE
An abrasion-resistant plate affixed to the bottom portion of a door to prevent a trap condition and protect its surface. Advisory Definition of KICK PLATE....
-
Accessible Exterior Surfaces
Accessible Exterior Surfaces This is an executive summary of the “Accessible Exterior Surfaces Technical Report” dated 24 April 1999....
-
1017.5 Tread Obstacles
EXCEPTION: Where the surface is other than asphalt, concrete, or boards, tread obstacles shall be permitted to not exceed 2 inches (50 mm) in height measured vertically to the highest point...