Standard roll-in type shower compartments shall be 30 inches (760 mm) wide minimum by 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
Search Results "Mitigating Measures"
Commonly Searched Documents
-
608.2.2 Standard Roll-In Type Shower Compartments
-
703.4.1 Height above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
M302.4.2 Clearance Around Base
The base of the diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination...
-
M301.4.2 Clearance Around Base
The base of diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the examination...
-
12112(b)(7)
impairs sensory, manual, or speaking skills, such test results accurately reflect the skills, aptitude, or whatever other factor of such applicant or employee that such test purports to measure...
-
D. Tools Needed
Tools Needed The following items are needed for the survey: A metal tape measure that is at least 20 feet long; A digital level or bubble level that is 24 inches long...
-
§104.13(b)
that impairs sensory, manual, or speaking skills, the test results accurately reflect the applicant's or employee's job skills, aptitude, or whatever other factor the test purports to measure...
-
12112(b)(7)
impairs sensory, manual, or speaking skills, such test results accurately reflect the skills, aptitude, or whatever other factor of such applicant or employee that such test purports to measure...
-
Verify Electrical
Measure to top or bottom of boxes 11B-308.1.1 Heights of all electrical switch boxes....
-
R103 Conventions (Section-by-Section Analysis)
Measurements are stated in metric and U.S. customary units, and each system of measurement is to be used independently of the other....
-
Verify Electrical
Measure to top or bottom of boxes 11B-308.1.1 Heights of all electrical switch boxes....
-
II-2.8000 Qualified individual with a disability
duration, and severity of the risk; 2) The probability that the potential injury will actually occur; and, 3) Whether reasonable modifications of policies, practices, or procedures will mitigate...
-
Notes
in the official National Formulary, or the United States Pharmacopeia, or any supplement to them, (2) intended for use in the diagnosis of disease or other conditions, or in the cure, mitigation...
-
Boating facilities. (Section-by-Section Analysis)
., with respect to boat slips and gangways) mitigate the burden on existing facilities?...
-
Boating facilities. (Section-by-Section Analysis)
., with respect to boat slips and gangways) mitigate the burden on existing facilities?...
-
What Testing Accommodations Must Be Provided?
entities must ensure that the test scores of individuals with disabilities accurately reflect the individual’s aptitude or achievement level or whatever skill the exam or test is intended to measure...
-
1630.11 Administration of tests
that impairs sensory, manual or speaking skills, the test results accurately reflect the skills, aptitude, or whatever other factor of the applicant or employee that the test purports to measure...
-
M302.4.1 Clearance in Base
The base of the diagnostic equipment shall provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum...
-
M301.4.1 Clearance in Base
The base of diagnostic equipment shall provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured...
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
M302.4.1 Clearance in Base
The base of the equipment shall provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured...
-
M301.4.1 Clearance in Base
The base of the equipment shall provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured...