Search Results "Ground Surface"
-
Figure 1005.3.2 Extended Ground or Deck Surface at Fishing Piers and Platforms – Drawing from the U.S. Access Board
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
11B-811.2 Clear floor or ground space
A clear floor or ground space complying with Section 11B-305 shall be provided....
-
11B-811.2 Clear floor or ground space
A clear floor or ground space complying with Section 11B-305 shall be provided....
-
GROUND FLOOR
A building may have one or more ground floors....
-
GROUND FLOOR
A building may have one or more ground floors....
-
1008.2.6.2 Use Zones
Ground surfaces located within use zones shall comply with ASTM F 1292 (1999 edition or 2004 edition) (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
R&D Workshop Trim-A-Slab Expansion Joint Repair
Trim-A-Slab is a replacement for rotted and old wood typically found between slabs in driveways and sidewalks. This wood was used during the slab construction, and is part of the...
-
GAP ARMOUR
GAP ARMOUR IS AN INNOVATIVE RUBBER MATERIAL ...that easily installs (with a rubber hammer) into open concrete expansion joints to completely seal and protect! Gap Armour can be...
-
Stabilizer Solutions StaLok Stabilizer Joint Sand
STABILIZED JOINT SAND THAT STAYS PUT BETWEEN PAVERS StaLok Paver Sand sets up strong and locks in between pavers. It allows water to drain and ‘heals’ itself. The sand repairs...
-
Exterior Surfaces
However, some natural surfaces, such as compacted earth, soil treated with consolidants, or materials stabilized and retained by permanent or temporary geotextiles (mesh), gridforms, or...
-
Surfaces of Trails
Trail surfaces must be firm and stable....
-
1017.2 Surface
This section requires the surface of trails, passing spaces, and resting intervals to be firm and stable. A firm trail surface resists deformation by indentations....
-
The Dipstick® Floor Profiler Tool
Calculates F-numbers for runs, sections, and surfaces on site Instantly produces profile graphs on site "Instant" downloading to desktop or laptop computer Automatic zeroing Prints...
-
Inpro Corporation JointMaster® AR Series Seal Expansion Joint Systems
, and chemicals Heat weldable for watertight seams Industry unique design creates crisp sightline and incorporates ribs on side faces to aid in pooling epoxy and adding surface...
-
§100.201 Ground floor
Ground floor means a floor of a building with a building entrance on an accessible route. A building may have more than one ground floor....
-
Front Entry
Water fountain for the relaxing sound of running water to reduce stress Video intercom which shows images of the visitor throughout the house and records visitor while...
-
ETA Questions: Interpretation of the "Changes in Level Are Not Permitted" Requirements
There are a number of places in the 2010 ADA Standards where the phrase "Changes in level are not permitted" occurs. However, the interpretation of this phrase is not clearly...
-
T302.4 Surface Discontinuities
Surface discontinuities shall be ½ inch (13 mm) high maximum and shall be beveled with a slope not steeper than 1:2. EXCEPTIONS: 1....
-
Check Writing Surfaces: ADA Standard Section 904.3.3
Where provided, check writing surfaces shall comply with 902.3....
-
11B-505.8 Surfaces
Handrail gripping surfaces and any surfaces adjacent to them shall be free of sharp or abrasive elements and shall have rounded edges....
-
11B-505.8 Surfaces
Handrail gripping surfaces and any surfaces adjacent to them shall be free of sharp or abrasive elements and shall have rounded edges....
