side wall or partition, except that the water closet shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum from the side wall or partition in the ambulatory accessible toilet compartment...
Search Results "Compartment Door"
-
604.9.1 Location
-
604.9.1 Location
side wall or partition, except that the water closet shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum from the side wall or partition in the ambulatory accessible toilet compartment...
-
404.2.6 Doors in Series and Gates in Series
The distance between two hinged or pivoted doors in series and gates in series shall be 48 inches (1220 mm) minimum plus the width of doors or gates swinging into the space....
-
F206.5 Doors, Doorways, and Gates
Doors, doorways, and gates providing user passage shall be provided in accordance with F206.5....
-
206.5 Doors, Doorways, and Gates
Doors, doorways, and gates providing user passage shall be provided in accordance with 206.5....
-
Doors, Doorways and Gates [§206.5 and §404]
Doors, Doorways and Gates [§206.5 and §404] Compliance is required for doors, doorways, and gates providing user passage on accessible routes....
-
18.1 Q. Is it necessary to provide usable doors when the door leads to an area of the dwelling that is not accessible, such as the door leading down to an unfinished basement...?
Within the dwelling unit, doors intended for user passage through the unit must meet the requirements for usable doors....
-
11B-604.9.1 Location
side wall or partition, except that the water closet shall be 17 inches (432 mm) minimum and 19 inches (483 mm) maximum from the side wall or partition in the ambulatory accessible toilet compartment...
-
R218 Doors, Doorways, and Gates
R218 Doors, Doorways, and Gates The SNPRM would revise R218 to read as follows: R218 Doors, Doorways, and Gates....
-
Hager Companies Security Pull P4E
Security Pull Materials: - Stainless steel Certification: - Meets ANSI A156.6 for J401 Pulls Note: - Requires reinforcing plate with an access plate and Torx screws for door edge...
-
1010.2.2 Hardware
Door handles, pulls, latches, locks and other operating devices on doors required to be accessible by Chapter 11A or 11B shall not require tight grasping, tight pinching or twisting of the...
-
1010.2.2 Hardware
Door handles, pulls, latches, locks and other operating devices on doors required to be accessible by Chapter 11A or 11B shall not require tight grasping, tight pinching or twisting of the...
-
604.1 General
Water closets and toilet compartments shall comply with 604.2 through 604.8....
-
604.1 General
Water closets and toilet compartments shall comply with 604.2 through 604.8....
-
604.1 General
Water closets and toilet compartments shall comply with 604.2 through 604.8....
-
404.2.7 Door and Gate Hardware
Handles, pulls, latches, locks, and other operable parts on doors and gates shall comply with 309.4....
-
604.1 General
Water closets and toilet compartments shall comply with 604.2 through 604.8....
-
11B-809.8.3 Door maneuvering clearance.
At the dwelling unit side of the primary entry doors, secondary exterior doors, and required exit doors maneuvering clearances shall be 44 inches (1118 mm) minimum in length measured...
-
404.2.6 Doors in Series and Gates in Series
The distance between two hinged or pivoted doors in series and gates in series shall be 48 inches (1220 mm) minimum plus the width of doors or gates swinging into the space....
-
11B-604.1 General
Water closets and toilet compartments shall comply with Sections 11B-604.2 through 11B-604.8....
-
11B-604.1 General
Water closets and toilet compartments shall comply with Sections 11B-604.2 through 11B-604.8....
-
Door and Signal Timing for Hall Calls [4.10.7], Door Delay for Car Calls [4.10.8]
Timing, based on the distance between the farthest call button and the elevator door, begins with visible and audible signaling of car arrival....
-
11B-604.1 General
Water closets and toilet compartments shall comply with Sections 11B-604.2 through 11B-604.8....
-
§ 38.127 Sleeping compartments
[See subsections ...]
