Standard test method for shock-absorbing properties of playing surface systems and materials. ASTM F355-95, Vol. 15.07....
Search Results "Side Transfer Surface"
-
Literature Cited
-
609 Grab Bars
Specifications address size, spacing, position, surfaces, fittings, and structural strength....
-
2.7 Tread Obstacles
Where tread obstacles exist on the surface of an ORAR, they shall not exceed 1 inch (25 mm) in height....
-
Landscape Forms Inc. 35 Stay Bench
A single divider leaves 32” of seating space on either side. Two dividers leave three 21” seating spaces....
-
Curbell Medical Specialty Call Cords
For patients with special needs (severe burns, paraplegics, quadriplegics, immobilized patients) Pneumatic device activated by patient’s breath Adjustable clamp fits side...
-
Roughness Calculation
If the crack depth was deep enough, the wheel would be suspended by the two sides of the surface and never hit the bottom as shown in Figure 122 {sic}....
-
Hill-Rom Uno™ 102 Patient Lift
This lift handles most lifting and transfering needs in these environments. ...
-
Subject testing
A study was designed to investigate a correlation between surface roughness and WBV exposure to WC users in an attempt to determine which surfaces should be considered acceptable....
-
K4
, drink, condiment, and tableware dispensers are provided, are dispensers and operating controls mounted no higher than 54 inches above the floor if clear floor space is provided for a side...
-
Jamb Signage
...are all elevator jambs provided with signs placed on both sides designating the floor with 2" minimum height raised letters and Braille characters centered at 60" above the finish floor...
-
I1a
For a side approach (clear floor space at least 30 inches long x 48 inches wide), is the coin slot no higher than 54 inches above the floor?...
-
4.17.4 Toe Clearances
In standard stalls, the front partition and at least one side partition shall provide a toe clearance of at least 9 in (230 mm) above the floor....
-
5e.
Are signs mounted on both sides of the elevator hoistway door opening that designate the floor with 2-inch minimum-height raised letters and Braille characters centered at 60 inches above...
-
Assembly Areas
where they adjoin seating and since accessible routes are required to connect to wheelchair seating locations, compliance with 4.9, including requirements for handrails, is not required at sides...
-
4.17.4 TOE CLEARANCES
In standard stalls, the front partition and at least one side partition shall provide a toe clearance of at least 9 in (230 mm) above the floor....
-
4.34.5.5(4) Controls
In the shower stall in Fig. 35(a), all controls, faucets, and the shower unit shall be mounted on the side wall opposite the seat....
-
Attachment H
Provide a paper towel dispenser with the controls a maximum height above the finished floor of 48 inches for a forward approach or 54 inches for a side approach and that is accompanied by...
-
5. Significance and Use
5.1 This practice provides a means for obtaining a quantitative estimate of a surface property defined as roughness using longitudinal profile measuring equipment. 5.1.1 The PRI is portable...
-
Story
That portion of a building included between the upper surface of a floor and upper surface of the floor or roof next above....
-
Aisle Seats
The proposed rule required that such seats have removable or folding armrests or no armrests on the aisle side....
-
1007.7.4 Separation
The fire-resistance-rated exterior wall construction shall extend horizontally 10 feet (3048 mm) beyond the landing on either side of the landing or equivalent fire-resistance-rated construction...
-
Water Closet Location and Rear Grab Bar
The 1991 Standards contain no exception for grab bar length, and require the water closet centerline to be exactly 18 inches from the side wall, while the 2010 Standards requirement allows...
-
308.1 General
These dimensions apply to either forward or side reaches....
-
308.1 General
These dimensions apply to either forward or side reaches....
