round of Disability Employment Initiative cooperative agreements, providing funds to nine states to improve education, training and employment opportunities and outcomes for youth and adults...
Search Results "Adult Dimension"
-
Disability Employment Initiative
-
Access-Able Designs Stationary Dressing Bench DST-101
Adult dressing bench to allow room for undressing/redressing in public rooms Complies w/ ADA 4.21.3 when properly installed....
-
Technical requirements
Technical requirements state the specific numbers, conditions, and measurements that are required (percent that must comply, dimensions, reach ranges, grades, trail width, and so forth)....
-
§ 38.4(b) Dimensional tolerances
All dimensions are subject to conventional engineering tolerances for material properties and field conditions, including normal anticipated wear not exceeding accepted industry-wide standards...
-
Scoping
Data provided by the Disability Statistics Center at the University of California, San Francisco demonstrated that the number of adults who use wheelchairs has been increasing at the rate...
-
11B-812.10.4 Location
Where the long dimension of a vehicle space is parallel to the vehicular way, the EV charger shall be adjacent to, and 48 inches (1219 mm) maximum from the head end or foot end of the vehicle...
-
11B-812.10.4 Location
Where the long dimension of a vehicle space is parallel to the vehicular way, the EV charger shall be adjacent to, and 48 inches (1219 mm) maximum from the head end or foot end of the vehicle...
-
Floor Plan of Elevator Cars [4.10.9]
The car dimensions specified in ADAAG are based on earlier accessibility guidelines developed in accord with industry standards....
-
M101.6 Dimensional Tolerances (Section-by-Section Analysis)
The MDE NPRM proposed that dimensions were to be subject to conventional industry tolerances for manufacturing processes, material properties, and field conditions....
-
407.12.3.2.2 Knee and Toe Space (Section-by-Section Analysis)
407.12.3.2.2 Knee and Toe Space (Section-by-Section Analysis) This section proposes dimensions for knee and toe space under ICT when an obstructed forward reach is provided....
-
Clear Floor Space [4.16.2]
the required clear floor space doors cannot swing into the clear floor space required at any fixture the 18 inch water closet centerline is absolute The 18 inch dimension...
-
M305.3 Standing Supports (Section-by-Section Analysis)
In the MDE NPRM preamble, the Access Board noted that it was considering adopting the cross section dimensions for grab bars from the 2004 ADA and ABA Accessibility Guidelines and applying...
-
The Market Case for Accessible Events, Meetings and Conferences
Vision: 20.6 Million According to the 2012 National Health Interview Survey (NHIS) Preliminary Report, an estimated 20.6 million adult Americans (or nearly 10% of all adult Americans)...
-
Elongated surface openings must be perpendicular to the dominant direction of travel, but what if there is no dominant direction of travel?
When there is no dominant direction of cross traffic, openings must be limited to ½” in both dimensions. ...
-
Elevator Car Requirements [§407.4]
Elevator Car Requirements [§407.4] The ADA Standards specify the minimum car dimensions....
-
DEFINITIONS AND OPERATIONAL CHARACTERISTICS OF ROAD AND TRAIL USERS
Earlier studies of inline skates, scooters, strollers, electric bicycles, adult tricycles, recumbents, tandems, bicycle trailers, golf carts, and assistive technologies are referenced and...
-
6. Do the ADA and Olmstead apply to persons at serious risk of segregation in sheltered workshops?
In the adult context, people with disabilities could show risk of segregation if a public entity systematically screens out adults with significant disabilities from vocational rehabilitation...
-
Care Management/Care Coordination
Meeting the needs of persons with disabilities is of increasing importance as individuals live longer and the prevalence of adults with functional limitations and disabilities rises....
-
Accessible Passenger Loading Zones [§503]
Accessible Passenger Loading Zones [§503] Requirements for accessible passenger loading zones address vehicle pull-up spaces and access aisles, including their dimensions, surfacing,...
-
M101.5 Dimensional Tolerances
Dimensions are subject to conventional industry tolerances for manufacturing processes, material properties, and field conditions. Question 5....
-
Subpart D—Preschool, Elementary, and Secondary Education
Subpart D sets forth requirements for nondiscrimination in preschool, elementary, secondary, and adult education programs and activities, including secondary vocational education programs...
-
R302.7.3 Horizontal Openings
Elongated openings in gratings shall be placed so that the long dimension is perpendicular to the dominant direction of travel....
-
4.1.6(3)(c)(ii)
(ii) Where existing shaft configuration or technical infeasibility prohibits strict compliance with 4.10.9, the minimum car plan dimensions may be reduced by the minimum amount necessary...
-
11B-703.7.2.1 International Symbol of Accessibility
A border may be provided inside or outside of the minimum required International Symbol of Accessibility dimension....
