provided other persons shall, before any procurement of an inaccessible vehicle, file with the appropriate state program office a certificate that it provides equivalent service meeting the standards...
Search Results "Industry Standard"
Filters
Commonly Searched Documents
-
§ 37.77(d)
-
Discrimination prohibited. (Section-by-Section Analysis)
One large State department of corrections objected to the entire section applicable to detention and correctional facilities, stating that it sets a higher standard for correctional and...
-
11B-604.2 Location
[2010 ADA Standards] 604.2 Location. The water closet shall be positioned with a wall or partition to the rear and to one side....
-
11B-213.3.6 Bathing facilities
[2010 ADA Standards] 213.3.6 Bathing Facilities....
-
11B-604.6 Flush controls
[2010 ADA Standards] 604.6 Flush Controls. Flush controls shall be hand operated or automatic. Hand operated flush controls shall comply with 309....
-
11B-1009.2.7 Operation
[2010 ADA Standards] 1009.2.7 Operation. The lift shall be capable of unassisted operation from both the deck and water levels....
-
Hager Companies Push/Pull Latch 311H
Hager Push/Pull Latch 311H: - New design replacing 311D - Engraving is available (optional) - Non-handed - Hospital latch Standard Materials: - Zinc and stainless...
-
1. Covered Entities
(See the discussion of industry comments on this issue in the section below entitled “Testing and Labeling of Electronic Respiratory Assistive Devices.”)...
-
804 Kitchens and Kitchenettes
The appliance industry called attention to certain types of doors that, when fully open, cannot easily meet this specification, such as dishwasher doors and doors of ovens and broilers that...
-
STATUTORY AND REGULATORY BACKGROUND
Previously, the television industry had voluntarily provided some television captioning....
-
Purpose of Proposed Rule
Moreover, recent technological changes in the movie theater industry—including wide-spread conversion from analog (film) projection to digital cinema systems—make exhibition of captioned...
-
Two-tiered definitional approach. (Section-by-Section Analysis)
While two business associations indicated that they opposed the concept of ‘‘other power-driven mobility device'' in its entirety, other business commenters expressed general and industry-specific...
-
Flush Controls on Toilets
Flush controls for tank-type toilets have a standardized mounting location on the left side of the tank (facing the tank)....
-
NetCentric Technologies Inc. CommonLook PDF Validator Software
Health and Human Services) standards. In addition, users can customize the checkpoints within any standard to fit the specific accessibility needs of their organization....
-
Allegion LCN 3030 Series Overhead Concealed Door Control
Features and Benefits The 3030 Series is UL and cUL listed with regular arm for self-closing doors Tested and certified under ANSI Standard A156.4, grade one Specifications...
-
Delta Single Handle Basin Faucet 570LF-WFHDF
Product Features and Benefits Drain assembly sold separately Meets standards set by Americans with Disabilities Act (ADA) 1.50 gpm @ 60 psi, 5.7 L/min @ 414 kPa...
-
Glenn Dea
Glenn has been employed in the architecture and construction industry since 1988....
-
Department of Labor, OFCCP Checklist for Compliance with Section 503
Purpose of Section 503: The Section 503 regulations set forth the standards for compliance with section 503 of the Rehabilitation Act of 1973, as amended (29 U.S.C. 793), which prohibits...
-
Assisted Living Directory - Texas Assisted Living Facilities & Senior Care Search
Type C facilities are 4-bed facilities that “meet the minimum standards and rules for enrollment in the DADS Adult Foster Care home program.”...
-
DOT Response
The Department continues to believe that standards based on Access Board guidelines for transportation vehicles are the appropriate basis for requirements pertaining to the design and construction...
-
Norton Surface Mounted Medium Duty 8000 Series Door Closer
Features: 8301/8501: Adjustable spring sizes 1-6 8301/8501: Tri-style® packaging standard (regular arm, top jamb and parallel arm mounting) 8300/8500: Sized springs 2, 3, 4, 5,...
-
PDQ 4200 Series Exit Device Door Hardware
All units come with touch bar components that are constructed of heavy gauge wrought steel or stainless steel as well as metal chassis covers and end caps Non fire rated devices come standard...
