Otherwise, fixed barriers detectable by canes must define areas with less clearance. Gates, rails, curbs, and other fixed elements, such as planters, can serve as barriers....
Search Results "Functional Area"
-
Head Room [4.4.2]
-
Special Technical Provisions for Alterations to Existing Buildings and Facilities [4.1.6(3)]
Special provisions also address stairs, elevators, doors, toilet rooms, assembly areas, platform lifts, and dressing rooms....
-
Can handrail extensions wrap or turn?
Extensions are not required for continuous handrails along switchback or dogleg ramps or at aisle ramps serving seating in assembly areas....
-
11B-608.1 General
Shower stalls that are 60 inches (1525 mm) wide and have no curb may increase the usability of a bathroom because the shower area provides additional maneuvering space....
-
505.3 Continuity
EXCEPTION: In assembly areas, handrails on ramps shall not be required to be continuous in aisles serving seating....
-
804.2.2 U-Shaped
In U-shaped kitchens enclosed on three contiguous sides, clearance between all opposing base cabinets, counter tops, appliances, or walls within kitchen work areas shall be 60 inches (1525...
-
802.1.2 Width
Figure 802.1.2 Width of Wheelchair Spaces in Assembly Areas...
-
Disability
(2) The phrase major life activities means functions such as caring for one's self, performing manual tasks, walking, seeing, hearing, speaking, breathing, learning, and working....
- Allegion Falcon 1490 Series Exit Devices
- Allegion Falcon 1790 Series Exit Devices
- Norton Surface Mounted 5700 Series Low Energy Door Operator
-
Assistive Listening Systems
In the final rule, the Board has added an exception for assembly areas where all seats are served by an induction loop system (219.3, Exception 2)....
-
TEST NO. 2 – SITE ANALYSIS TEST
Calculate the percentage of the total buildable area of the undisturbed site with a natural grade less than 10-percent slope....
-
Reduced scoping for public accommodations, small facilities, and qualified small businesses. (Section-by-Section Analysis)
Department's initial regulatory assessment, the Department has identified ten elements for which the Department believes reduced scoping might be appropriate for barrier removal: play areas...
-
Effect on the certification process of using more than one regulatory scheme at the state or local level to establish accessibility requirements for title III facilities with new design requirements in the proposed standards. (Section-by-Section Analysis)
proposed standards will include requirements for elements and spaces that are not addressed specifically in the 1991 Standards, including elements within recreational facilities and play areas...
-
711.4.1 Through penetrations
Penetrating items with a maximum 6 inch (152 mm) nominal diameter shall not be limited to the penetration of a single fire-resistance-rated floor assembly provided that the area of the penetration...
-
Subpart D -- New Construction and Alterations (Section-By-Section Analysis and Response to Comments)
Potential patrons of places of public accommodation, such as retail establishments, should be able to get to a store, get into the store, and get to the areas where goods are being provided...
-
11B-233.3.1.2.6.3 Test number two, site analysis test
Calculate the percentage of the total buildable area of the undisturbed site with a natural grade less than 10 percent slope....
- Biodex Upper Body Cycle
-
Safe Harbor
The 2010 Standards reduced scoping requirements for accessible seating in large assembly areas....
-
§382.3 Facility
., structures, roads, walks, parking lots, ticketing areas, baggage drop-off and retrieval sites, gates, other boarding locations, loading bridges) normally used by passengers or other members...
-
1007 Miniature Golf Facilities
All level areas of an accessible hole where a ball may come to rest are to be within golf club reach of the accessible route....
-
F211.1 General
Where drinking fountains are provided on an exterior site, on a floor, or within a secured area they shall be provided in accordance with F211....
-
Turning Space [1015.4]
least 60 inches in diameter or a T-shaped space with an arm at least 60 by 36 inches and a base at least 36 inches wide by 24 inches long (figure 29) must be provided within the viewing area...