18 Degree Door Pull 990P Materials:- Brass, bronze, stainless steel...
Search Results "Surface Material"
-
Hager Companies 18 Degree Door Pull 990P
-
Hager Companies Coat Hook - Long Single 902P
Coat Hook - Long Single 902P Material: - Brass Notes: - Concealed mounting...
-
Hager Companies S-Shaped Door Pull 932P
S-Shaped Door Pull Materials:- Aluminum, brass, bronze, stainless steel...
-
Hager Companies C-Shaped Door Pull 920P
C-Shaped Door Pull Materials: - Aluminum, brass, bronze, stainless steel...
-
Hager Companies C-Shaped Door Pull 920B
C-Shaped Door Pull Materials: - Aluminum, brass, bronze, stainless steel...
-
Hager Companies C-Shaped Door Pull 925B
C-Shaped Door Pull Materials: - Aluminum, Brass, Bronze, Stainless Steel...
-
Hager Companies Offset Door Pull 934P
Offset Door Pull 934P Materials:- Aluminum, brass, bronze, stainless steel...
-
Hager Companies Double Curved Door Pull 987P
Double Curved Door Pull 987P Materials:- Brass, bronze, stainless steel...
-
Hager Companies S-Shaped Door Pull 932B
S-Shaped Door Pull Materials:- Aluminum, brass, bronze, stainless steel...
-
Hager Companies Straight Segment Shape Door Pull 980B
Straight Segment Shape Door Pull Materials: - Brass, bronze, stainless steel...
-
Hager Companies C-Shaped Door Pull 925P
C-Shaped Door Pull Materials: - Aluminum, Brass, Bronze, Stainless Steel...
-
Hager Companies Coat Hook - Short Single 901P
Coat Hook - Short Single 901P Material: - Brass Notes: - Concealed mounting...
-
Hager Companies Coat Hook - Long Double 903P
Coat Hook - Long Double 903P Material: - Brass Notes: - Concealed mounting...
-
Hager Companies C-Shaped Door Pull - Continuous 922B
C-Shaped Door Pull - Continuous Materials: - Brass, bronze, stainless steel...
-
Hager Companies Offset Segment Shape Door Pull 981B
Offset Segment Shape Door Pull Materials: - Brass, bronze, stainless steel...
-
11B-703.7.2.5 Cleaner Air Symbol
There shall be at least a 70-percent color contrast between the background of the sign from the surface that it is mounted on. FIGURE 11B-703.7.2.5 ‡‡ CLEANER AIR SYMBOL...
-
704.4.1 Height
When in use, the touch surface of TTY keypads shall be 34 inches (865 mm) minimum above the finish floor....
-
Companion Seats
with the ANSI A117.1‒2003 standard, the provision in the final rule specifies that shoulder alignment is to be measured 36 inches from the front of the wheelchair space and that the floor surface...
-
Sloped Entries
Sloped Entries Sloped entries must comply with ADAAG accessible route provisions (36 inch minimum width, maximum 1:12 or 8.33% slope), except that the surface does not need to be slip...
-
Maneuvering Space
Objects are not permitted to protrude into ground level maneuvering spaces at or below 80 inches (2030 mm) above the ground or floor surface....
-
BENEFITS AND COSTS: OVERVIEW
BENEFITS AND COSTS: OVERVIEW Based on our analysis, we determined that transfer surface height requirements lower than 19 inches would increase the cost of designing and manufacturing...
-
QUESTION: WHAT LIMITATIONS CAN A PVO IMPOSE WITH RESPECT
TO CARRYING A SERVICE ANIMAL?
* For example, a PVO could impose a legitimate safety requirement that a service dog not be permitted to enter a sauna or steam room, sit on any surface other than the floor, or join...
-
R309.4 Curb Ramps or Blended Transitions
Detectable warning surfaces are not required on curb ramps and blended transitions that connect the access aisle to the sidewalk, including where the sidewalk is at the same level as the...
-
Parallel Parking Spaces (R309.2) (Section-by-Section Analysis)
The access aisle must not encroach on the vehicular travel lane and comply with the technical requirements for surfaces (see R302.7)....
