The MDE Advisory Committee recognized that certain individuals at the extreme end of the weight continuum may have difficulty accessing medical diagnostic equipment without specific accommodations...
Search Results "End Transfer Surface"
Filters
Commonly Searched Documents
-
8.1 Excluded Populations Needing Future Attention
-
11B-1009.2.2 Seat location
The deck surface between the centerline of the seat and the pool edge shall have a slope not steeper than 1:48. FIGURE 11B-1009.2.2 POOL LIFT SEAT LOCATION...
-
904.4.2 Forward Approach
A portion of the counter surface that is 30 inches (760 mm) long minimum and 36 inches (915 mm) high maximum shall be provided....
-
904.4.2 Forward Approach
A portion of the counter surface that is 30 inches (760 mm) long minimum and 36 inches (915 mm) high maximum shall be provided....
-
R409.10.3 Bottom Extension at Stairways
Extensions shall return to a wall, guard, or the landing surface, or shall be continuous to the handrail of an adjacent stair flight....
-
4.17.6 Grab Bars
Grab bars may be mounted with any desired method as long as they have a gripping surface at the locations shown and do not obstruct the required clear floor area....
-
R409.10.2 Top Extension at Stairways
Extensions shall return to a wall, guard, or the landing surface, or shall be continuous to the handrail of an adjacent stair flight....
-
4.17.6 GRAB BARS
Grab bars may be mounted with any desired method as long as they have a gripping surface at the locations shown and do not obstruct the required clear floor area....
-
11B-503.3.3 Marking
The area within the borderlines shall be marked with hatched lines a maximum of 36 inches (914 mm) on center in a color contrasting with that of the aisle surface....
-
11B.707.7.1.1 Vertically mounted display screen
or tipped away from the viewer less than 30 degrees, the center line of the display screen and other display devices shall be no more than 52 inches (1321 mm) above the floor or ground surface...
-
CASI California Survey Reports Acceptance Criteria - Field Tolerances AC 03-12
All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points....
-
Contrast and wayfinding, short-term and long-term
We went in to talk with Susan and you know she’d never even thought about that and we ended up talking an hour and it was very fun to sort of understand where her light bulb sort of started...
-
Section 36.204 Administrative Methods (Preamble, Section-by-Section Analysis)
Both sections incorporate a disparate impact standard to ensure the effectiveness of the legislative mandate to end discrimination....
-
Accessibility Engineering Specialists
The Board encourages any efforts to move accessibility design into the mainstream of telecommunications and will work cooperatively with any established group to further those ends....
-
3. MINIMUMS, MAXIMUMS AND SPECIFYING AT THE LIMIT
It will also more often produce an end result of strict and literal compliance with the stated requirements and eliminate enforcement difficulties and issues that might otherwise arise....
-
Wheelchair Accessible Gates
Web sites with designs that allow wheelchair access while restricting access by ATVs and motorcycles are listed near the end of this tech tip....
-
1. New Format for Guidelines
published in 2004, we submitted the guidelines, as amended by the final rule, to the Federal Register as a Word document without figures, except for four mandatory symbols included at the end...
-
3.1 Plan Ahead
., it’s on the same side of the street as the bus stop, the first entrance at the end of the block after you get off the bus)?...
-
After Completing the Survey
For more information about temporary modifications, see Temporary Solutions for Election Day at the end of each section of this document....
-
4.3.5 Turning clearance
In confined dead end spaces, a 360-degree turn should be used as the basis for the minimum space required since individuals often move around within small space without actually leaving...
-
4.16.6 Dispensers
Alternatively, Horty Elving and Associates used a toilet paper holder at the end of each swing-away grab bar (e.g., Figure 11) at Bridges Medical Services, Ada, MN (Horty, Elving & Associates...
-
705.1.2 Dome Spacing
Truncated domes in a detectable warning surface shall have a center-to-center spacing of 1.6 inches (41 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch...
-
Seat Height
Seat Height The lift must be designed so that the seat will make a stop between a minimum of 16 inches and maximum of 19 inches (measured from the deck to the top of the seat surface,...
-
11B-505.10.1 Top and bottom extension at ramps
Extensions shall return to a wall, guard, or the landing surface, or shall be continuous to the handrail of an adjacent ramp run....