Housing at a place of education that is subject to this part shall comply with the provisions of the 2010 Standards applicable to transient lodging, including, but not limited to, the requirements...
Search Results "Subject Matter Expert"
-
11B-224.7.2 Multi-bedroom housing units with adaptable features
-
E. IMPLEMENTATION AND ENFORCEMENT
with this Agreement or any requirements contained herein, the United States agrees to notify the Museum in writing of the alleged noncompliance and attempt to seek a resolution of the matter...
-
The Basis for the 2010 ADA Standards Pocket Guide
Learn the basis of the 2010 ADA Standards Pocket Guide
-
Alterations to Vacated Buildings: ADA Standard Section 233.3.4.1
Section 233.3.4.1 covers scoping requirements in the current ADA Standards for alterations to vacated buildings.
-
1.9.1.1 Application
to a state, county, municipality or other political subdivision of the state, the entity that collects and controls the distribution of the public funds becomes the funding source, and subject...
-
1.9.1.1 Application
to a state, county, municipality or other political subdivision of the state, the entity that collects and controls the distribution of the public funds becomes the funding source, and subject...
-
Re: Caution regarding minimum Aisle Widths for aisles that serve "elements on both sides"
This reminds me of quordle—every word choice matters, just like every design decision can affect user experience. Always good to verify with the AHJ!...
-
Q1.) When a ramp has a maximum slope of 1:12 or 8.33%, is that considered a range of from 0% to 8.33% which would allow no slope greater than 8.33% or is that a simple maximum which would allow a tolerance above 8.33%? Similarly, is a cabinet countertop that can be no higher than 34” AFF a range of from 0” to 34” AFF with no additional height allowed, or is a tolerance allowed for variations in the floor surface or cabinet construction?
The consistent technical assistance on this question has been that both are subject to tolerances....
-
Sec. 469.107(1)
(1) review plans and specifications and make inspections of a structure not otherwise subject to this chapter; and...
-
§27.7(b)(4)(i)
(i) That have the effect of subjecting qualified persons with a disability to discrimination on the basis of disability,...
-
§104.4(b)(4)(i)
(i) that have the effect of subjecting qualified handicapped persons to discrimination on the basis of handicap,...
-
§35.130(b)(3)(i)
(i) That have the effect of subjecting qualified individuals with disabilities to discrimination on the basis of disability;...
-
E101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range....
-
C101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range....
-
§ 35.130(b)(3)(i)
(i) That have the effect of subjecting qualified individuals with disabilities to discrimination on the basis of disability;...
-
T215 Communication Features
(Section T702, in turn, addresses such matters as character style and height, line spacing, and contrast.) See 2010 NPRM, Sections T203.10.2, T702....
-
12188(a)(1) Availability of remedies and procedures
remedies and procedures The remedies and procedures set forth in section 2000a-3(a) of this title are the remedies and procedures this subchapter provides to any person who is being subjected...
-
§ 37.33(a)
Transportation systems operated by public airport operators, which provide designated public transportation and connect parking lots and terminals or provide transportation among terminals, are subject...
-
406.8 Detectable Warnings
Curb ramps subject to Department of Transportation regulation 49 CFR 37.21 shall have a detectable warning complying with 705....
-
A. Background
This matter was initiated by a complaint filed with the United States Department of Justice (the “Department”) against Jefferson Outpatient under Title III of the Americans with Disabilities...
-
M101.6 Dimensional Tolerances
Dimensions are subject to conventional industry tolerances for manufacturing processes, material properties, and field conditions....
-
504.7 Wet Conditions
Stair treads and landings subject to wet conditions shall be designed to prevent the accumulation of water....
-
225(e)(1) In general
(1) In general Subject to subsections (f) and (g) of this section, the Commission shall enforce this section....
-
11B-504.7 Wet conditions
Stair treads and landings subject to wet conditions shall be designed to prevent the accumulation of water....