Truncated domes in a detectable warning surface shall have a center-to-center spacing of 2.3 inches (58 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch...
Search Results "Convention Center"
Filters
Commonly Searched Documents
-
11B-705.1.1.2 Dome spacing
-
11B.707.7.1.2 Angle-mounted display screen
Where display screens are mounted tipped away from the viewer 30 degrees to less than 60 degrees from vertical, the center line of the display screen and other display devices shall be no...
-
2. REGULATORY BUILT-IN TOLERANCES
REGULATORY BUILT-IN TOLERANCES: California Building Code Section 1101B.5 indicates all dimensions are subject to conventional industry tolerances except where the requirement is stated as...
-
Using TTYs
Certain conventions are standard, such as typing "GA" (go ahead) after each message; this tells the other person on the line to begin typing a response....
-
F212.3 Sinks
Exception 2 exempts sinks in camping facilities and picnic facilities where a cooktop or conventional range is not provided....
-
Audio Induction Loop
Loop systems are readily integrated with conventional sound systems and relatively easy to maintain....
-
11B-104.1.1 Construction and manufacturing tolerances
All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points....
-
11B-104.1.1 Construction and manufacturing tolerances
All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points....
-
The Global Initiative for Inclusive ICT
Communication Technologies – is an advocacy initiative launched in December 2006 by the United Nations Global Alliance for ICT and Development, in cooperation with the Secretariat for the Convention...
-
11B-705.1.1.2 Dome spacing
Truncated domes in a detectable warning surface shall have a center-to-center spacing of 2.3 inches (58 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch...
-
Keypads: ADA Standard Section 407.4.7.2
Section 407.4.7.2 covers the current ADA Standards for designations and indicators on elevator keypads.
-
Standard Roll-In Type Shower Compartments: ADA Standard Section 608.2.2
Section 608.2.2 covers the current ADA Standards for the size of standard roll-in type shower compartments.
-
11B-503.3.3 Marking
The area within the borderlines shall be marked with hatched lines a maximum of 36 inches (914 mm) on center in a color contrasting with that of the aisle surface....
-
Construction and Manufacturing Tolerances
The ADA Standards recognize conventional industry tolerances for dimensions not expressed as a range. This applies to field work, not design work....
-
Transfer Space: ADA Standard Section 1008.3.1.3
The 48 inch (1220 mm) long minimum dimension of the transfer space shall be centered on and parallel to the 24 inch (610 mm) long minimum side of the transfer platform....
-
Alternate Roll-In Type Shower Compartments: ADA Standard Section 608.2.3
Section 608.2.3 covers the current ADA Standards for the size and clearances of alternate roll-in type shower compartments.
-
11B-608.2.3 Alternate roll-in type shower compartments
Alternate roll-in type shower compartments shall be 36 inches (914 mm) wide and 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
11B-705.1.1.2 Dome spacing
Truncated domes in a detectable warning surface shall have a center-to-center spacing of 2.3 inches (58 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch...
-
ADA Training
Here are a few training possibilities: ADA National Network Centers The ten ADA Centers and their state affiliates provide training on every aspect of the ADA. ...
-
§1193.33(a)(3)
(3) Ensuring usable customer support and technical support in the call centers and service centers which support their products at no additional charge....
-
F104.1.1 Construction and Manufacturing Tolerances
All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points....
-
Section 36.406(f)(3)
Through its enforcement actions, the Department discovered that some venues place wheelchair spaces and companion seats on temporary platforms that, when removed, reveal conventional seating...
-
11B-104.1.1 Construction and manufacturing tolerances
All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points....
-
1. Introduction
You would like to find a usable fitness center, some times called a health club. The process of looking for a fitness center can be trying....
