Floor or ground surfaces of a turning space shall comply with Section 11B-302. Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted. Exception:...
Search Results "Bus Rapid Transit"
-
11B-304.2 Floor or ground surfaces
-
Floor or Ground Surfaces: ADA Standard Section 304.2
Section 304.2 covers the current ADA Standards for the ground surfaces of a turning space.
-
11B-304.2 Floor or ground surfaces
Floor or ground surfaces of a turning space shall comply with Section 11B-302. Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted. Exception:...
-
Does a wheelchair user have to use the seat belt and shoulder harness?
Under the broad nondiscrimination provisions in Section 37.5 of the DOT ADA regulations, a transit operator is not permitted to mandate the use by wheelchair users of seat belts and...
-
Clear Width of Circulation Paths and Maneuvering Clearances at Wheelchair Spaces
Otherwise, the transit community uniformly opposed the clearances proposed in the 2010 NPRM....
-
10.3.1(12)(a)
(a) If an interior public pay telephone is provided in a transit facility (as defined by the Department of Transportation) at least one interior public text telephone shall be provided in...
-
Does a wheelchair user have to use the seat belt and shoulder harness?
Under the broad nondiscrimination provisions in Section 37.5 of the DOT ADA regulations, a transit operator is not permitted to mandate the use by wheelchair users of seat belts and shoulder...
-
A. TITLE II OF THE ADA
Public entities are directed to develop a "transition plan" to "achieve program accessibility" by "setting forth the steps necessary to complete such changes." 28 C.F.R. § 35.150(d)(1);...
-
R304.1 General
Curb ramps and blended transitions shall comply with R304. Advisory R304.1 General....
-
R304.5.1.1 Pedestrian Circulation Paths Other Than Shared Use Paths
In pedestrian circulation paths other than shared use paths, the clear width of curb ramp runs, blended transitions, and turning spaces shall be 1.2 m (4.0 ft) minimum....
-
II-8.1000 General
In addition, public entities with 50 or more employees are required to -- 1) Develop a grievance procedure; 2) Designate an individual to oversee title II compliance; 3) Develop a transition...
-
T402 Ramps and Bridgeplates
bridgeplates in the 2016 Non-Rail Vehicle Guidelines include provisions on design load, installation and operation, emergency operation, surfaces, clear width, edge guards, running slope, transitions...
-
T201.1 General
Non-rail vehicles purchased, leased or remanufactured by entities covered by the Americans with Disabilities Act (ADA) shall comply with the requirements in the Non-Rail Vehicle...
-
§ 38.155(a)
(a) Handrails and stanchions shall be provided in the entrance to the vehicle in a configuration which allows passengers to grasp such assists from outside the vehicle while starting...
-
Figure 303.2 Vertical Change in Level – Drawing from the U.S. Access Board
-
11B-206.2.19 Pedestrian street crossings
Where walks or sidewalks are provided, a curb ramp, blended transition, or a combination of curb ramps and blended transitions complying with Section 11B-406 shall connect the walks or sidewalks...
-
§ 38.159(c)(3) Ramp threshold
The transition from roadway or sidewalk and the transition from vehicle floor to the ramp may be vertical without edge treatment up to 1/4 inch (6.5 mm)....
-
Questions presented:
Is the replacement of a staircase at an existing public transportation facility an “alteration” that affects or could affect the usability of a facility for purposes of the ADA...
-
§ 38.55(b)
(b) Characters on signs required by paragraph (a) of this section shall have a width-to-height ratio between 3:5 and 1:1 and a stroke width-to-height ratio between 1:5 and 1:10, with...
-
Transportation Facilities: ADA Standard Section 217.4.7
Section 217.4.7 covers scoping requirements in the current ADA Standards for TTYs in transportation facilities.
-
T402.6 Clear Width
The clear width of ramps and bridgeplates shall be 30 inches (760 mm) minimum.
-
T402.1 General
Ramps and bridgeplates shall comply with T402. Ramps and bridgeplates shall be permitted to fold or telescope.
-
T402.2 Design Load
Ramps and bridgeplates 30 inches (760 mm) or more in length shall be designed to support a load of 600 pounds (273 kg) minimum, placed at the centroid of the ramp distributed over an...
-
T402.8 Running Slope
The maximum running slope of ramps and bridgeplates shall comply with T402.8.1 or T402.8.2.
