These standards are intended to be consistent to those contained in the 2010 Standards for Accessible Design, and are generally the same except as noted in italics....
Search Results "Fire and Safety Standard"
-
101.1 General
-
R105 Definitions (Section-by-Section Analysis)
Collegiate dictionaries are used to determine the meaning of terms that are not defined in the proposed guidelines, referenced MUTCD standards, or regulations issued by federal agencies...
-
Q5: Should a school district revise its policies and procedures regarding the determination of coverage and provision of services under Section 504 and Title II?
A: Yes, if those policies and procedures do not implement the Amendments Act's new legal standards....
-
Introduction
recommendations on best practices for physical accessibility and customer service that go above and beyond the minimum requirements contained within the 2010 Americans with Disabilities Act (ADA) Standards...
-
A.2.ii. - Should EIT be compatible with assistive technology?
In some cases, the standards require that the acquired EIT be readily usable without the need for assistive devices....
-
Are self-evaluations and transition plans required to be updated?
Although there is no requirement to update them, updating is the best means to ensure compliance with current regulations and design standards. A lot has changed in 27 years....
-
Minimum Clear Headroom
The commenters stated that standard doors provide a height range from 75 to 79 inches, and that an 80-inch specification would considerably increase the cost of each door installed....
-
407.7 Color (Section-by-Section Analysis)
The proposed section is the same as existing 508 Standards § 1195.25(g), and is consistent with 255 Guidelines § 1193.41(c)....
-
E102.5 Internet Engineering Task Force (IETF)
Copies of the referenced standard may be obtained from the Internet Engineering Task Force (http://www.ietf.org/)....
-
4.10.12(2)
All control buttons shall be designated by Braille and by raised standard alphabet characters for letters, arabic [sic] characters for numerals, or standard symbols as shown in Fig. 23(a...
-
Mirrors [4.19.6]
The mounting height of the bottom of mirrors at accessible lavatories (40 inches maximum above the floor) is based on the standard eye level range of adults seated in wheelchairs (43 to...
-
205 Operable Parts
1991 Standards for Accessible Design 2010 Standards for Accessible Design What’s New/Different 4.1.3(13) Controls...
-
223 Medical Care and Long-Term Care Facilities
1991 Standards for Accessible Design 2010 Standards for Accessible Design What’s New/Different 6.1 General....
-
4.10.12(2)
All control buttons shall be designated by raised standard alphabet characters for letters, arabic characters for numerals, or standard symbols as shown in Fig. 23(a), and as required in...
-
Elevators
All passenger elevators must meet the requirements of the Standards. ADA Standards 4.1.3(5); 4.10....
-
11B-608.4 Seats
[2010 ADA Standards] 608.4 Seats. A folding or non-folding seat shall be provided in transfer type shower compartments....
-
11B-221.2.1.1 General seating
5 301 to 500 6 501 to 5000 6, plus 1 for each 100, or fraction thereof, between 501 through 5000 [2010 ADA Standards...
-
Section 36.311 Mobility Devices (Section-by-Section Analysis)
If a facility complies with the applicable design requirements in the 1991 Standards or the 2010 Standards, the public accommodation will not be required to exceed those standards to accommodate...
-
Van Accessible Parking Spaces
The 1991 Standards, at sections 4.1.2 (5)(b), 4.6.3, 4.6.4, and 4.6.5, require one in every eight accessible parking spaces to be van accessible....
-
9. Outdoor Developed Areas
The Board has issued requirements that are now part of the Architectural Barriers Act (ABA) Accessibility Standards and apply to national parks and other outdoor areas developed by the federal...
-
Section 35.151(d) Scope of coverage
Although the Department may use the requirements of the 2010 Standards as a guide to determining when and how to make equipment and furnishings accessible, those determinations fall within...
-
M101.6 Dimensional Tolerances (Section-by-Section Analysis)
manufacturers and one medical association) indicated that tolerances vary based on the manufacturer, product design, and manufacturing process and that they are unaware of any industry standard...
-
9. Outdoor Developed Areas
The Board has issued requirements that are now part of the Architectural Barriers Act (ABA) Accessibility Standards and apply to national parks and other outdoor areas developed by the federal...
-
T603.5 Securement Systems for Rear-Facing Wheelchair Positions
accessible transport vehicles designed for use by both sitting and standing passengers — Part 1: Systems for rearward facing wheelchair-seated passengers, First Edition, June 5, 2012 [ISO Standard...