The top of the bench seat surface shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the finish floor or ground. ...
Search Results "Ramp Surface"
-
903.5 Height
-
11B-903.5 Height
The top of the bench seat surface shall be 17 inches (432 mm) minimum and 19 inches (483 mm) maximum above the finish floor or ground....
-
11B-813.2.1.1 Size
Adult changing tables shall have a changing surface of 70 inches (1778 mm) minimum length and 30 inches (762 mm) minimum width....
-
11B-903.5 Height
The top of the bench seat surface shall be 17 inches (432 mm) minimum and 19 inches (483 mm) maximum above the finish floor or ground....
-
Radiologic Equipment
Most of these technologies require the patient to lie on a flat surface that is part of the equipment....
-
Transfer Access [1014.2.1]
The surface of the clear ground space must be firm and stable....
-
Modifications to the Longitudinal Study
By the end of 2006, NCA had initial commitments from a number of state or federal outdoor recreation entities to provide test sites for the trail surface study, however, the down turn in...
-
Construction and Maintenance Practices
An accessible surface is firm and stable. Use caution with the size and depth of gravel when maintaining unpaved surfaces....
-
11B-808.3 Clear floor space
alterations, wheelchair spaces are not required to be located within the defined area of raised jury boxes or witness stands and shall be permitted to be located outside these spaces where ramp...
-
Evaluate and adjust the volume of the Walk indication
Evaluate and adjust the volume of the Walk indication Stand at the curb or end of the curb ramp at the crosswalk and listen for the Walk indication....
-
§27.72(b)
(b) Airports shall, in cooperation with carriers serving the airports, provide boarding assistance to individuals with disabilities using mechanical lifts, ramps, or other devices that do...
-
STREETS, ROADS AND WALKWAYS {35.150}
STREETS, ROADS AND WALKWAYS {35.150} “If a public entity has responsibility or authority over streets, roads, or walkways, its transition plan shall include a schedule for providing curb ramps...
-
Problem Two
As a temporary solution for election day, use traffic cones to mark off the access aisle and curb ramp area....
-
Portable Units [4.1.2(6)]
Where ramps are provided, it is important that required door clearances are available at the required level landing....
-
4.5.2 Changes in Level
Changes in level greater than 1/2 in (13 mm) shall be accomplished by means of a ramp that complies with 4.7 or 4.8....
-
4.5.2 CHANGES IN LEVEL
Changes in level greater than 1/2 in (13 mm) shall be accomplished by means of a ramp that complies with 4.7 or 4.8....
-
Stairways [ADA Standards §210, §504]
., ramp or elevator) are not required to meet the ADA Standards, but handrails must comply when the stairs are altered (§210.1, Ex. 2)....
-
§ 38.95(a)(1) General
., lift, ramp or bridge plate) complying with either paragraph (b) or (c) of this section; sufficient clearances to permit a wheelchair or mobility aid user to reach a seating location;...
-
11B-808.3 Clear floor space
alterations, wheelchair spaces are not required to be located within the defined area of raised jury boxes or witness stands and shall be permitted to be located outside these spaces where ramp...
-
11B-808.3 Clear floor space
alterations, wheelchair spaces are not required to be located within the defined area of raised jury boxes or witness stands and shall be permitted to be located outside these spaces where ramp...
-
210 and 504 Stairways
., where the accessible route is provided by an elevator, lift, or ramp)....
-
Preliminary Guidelines for SEWF Installation
Do not saturate surface with these lubricants. After compaction the thickness will be approximately 40 mm (1.6 in.). 3....
-
11B-705.1.2.1 Platform edges
Detectable warning surfaces at platform boarding edges shall be 24 inches (610 mm) wide and shall extend the full length of the public use areas of the platform....
-
1002.6.2 Transfer Height
The height of transfer device seats shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....