A religious corporation, association, educational institution, or society may give a preference in employment to individuals of the particular religion, and may require that applicants and...
Search Results "Applicable Standard"
Filters
Commonly Searched Documents
-
Section 1630.16(a) Religious Entities
-
III. Costs and Benefits
Second, the reasonable modification/accommodation requirements contained in this final rule are not very different from the origin-to-destination requirement already applicable to complementary...
-
4.1.4(12) STORAGE
Dairy products Beer or wine up to 12 percent alcohol Distribution transformers Cement in bags Electrical insulators Gypsum board Inert pigments Dry insecticides Application...
-
Clear Width [§405.5]
The width of ramps that are part of a means of egress may further be determined by applicable life safety codes and requirements for minimum exit widths greater than 36”....
-
General: ADA Standard Section 702.1
Fire alarm systems shall have permanently installed audible and visible alarms complying with NFPA 72 (1999 or 2002 edition) (incorporated by reference, see “Referenced Standards” in Chapter...
-
Dimensions: ADA Standard Section 810.2.2
Access Board’s Note to Reader: The Department of Transportation’s ADA standards indicate that compliance is required to the extent construction specifications are within a public entity's...
-
Guest Rooms with Communication Features: ADA Standard Section 806.3
For headset or external amplification system compatibility, a standard subminiature jack installed in the telephone will provide the most flexibility....
-
Caroma® USA Sydney Smart Point 8 Toilet
Due to the substantial water saving benefits achieved by the 1.0/0.7 gpf (3.8/2.8 L) dual flush system, the toilet is suitable for multi-purpose applications where water conservation is...
-
230 and 708 Two-Way Communication Systems
230 and 708 Two-Way Communication Systems New provisions of the 2010 Standards at sections 230.1 and 708 require two-way communications systems to be equipped with visible as well as...
-
§382.13(a)
As a carrier, you must modify your policies, practices, and facilities when needed to provide nondiscriminatory service to a particular individual with a disability, consistent with the standards...
-
E202.7.2 Alternative Means
Where ICT that fully conforms to the Revised 508 Standards is not commercially available, the agency shall provide individuals with disabilities access to and use of information and data...
-
§ 36.406(a)(2)
(2) New construction and alterations subject to this part shall comply with the proposed standards if physical construction of the property commences on or after [date six months after the...
-
§ 36.406(a)(1)
(1) New construction and alterations subject to this part shall comply with the 1991 Standards if physical construction of the property commences before [date six months after the effective...
-
f-v
[ADA Standards §§ 4.11.2, 4.27.3] Yes No...
-
I3
[ADA Standards § 4.31.9 (2)] Yes No...
-
M21
[ADA Standards § 4.25.3] Yes No...
-
K5
[ADA Standards § 5.5] Yes No...
-
B2
[ADA Standards § 4.6.3] Yes No...
-
Sec.36.308(b) New construction and alterations
The provision and location of wheelchair seating spaces in newly constructed or altered assembly areas shall be governed by the standards for new construction and alterations in subpart...
-
4.1.6(1)(e)
alteration work is limited solely to the electrical, mechanical, or plumbing system and does not involve the alteration of any elements and spaces required to be accessible under these standards...
-
A4.8.5 HANDRAILS
The requirements for stair and ramp handrails in this standard are for adults....
-
§1193.51(e) TTY signal compatibility
Products, including those providing voice communication functionality, shall support use of all cross-manufacturer non-proprietary standard signals used by TTYs....
-
§ 35.151(j)(1)
dwelling units designed and constructed or altered by public entities that will be offered for sale to individuals shall comply with the requirements for residential facilities in the 2010 Standards...
-
§ 38.4(b) Dimensional tolerances
All dimensions are subject to conventional engineering tolerances for material properties and field conditions, including normal anticipated wear not exceeding accepted industry-wide standards...
