Transfer Surface Size – M301.2.2 Supine, Prone, or Side-Lying Position The issues were discussed and decided in the full committee meeting as follows: depth of 17 inches minimum and width...
Search Results "Side Reach"
Filters
Commonly Searched Documents
-
Transfer Surface Size – M301.2.2 Supine, Prone, or Side-Lying Position
-
Wheelchair Transfer
ADAAG specifications are based on three types of transfer: diagonal, perpendicular, and side, some of which are illustrated in ADAAG Appendix Figure A6....
-
Recessed Doors and Gates [§404.2.4.3]
If any obstruction within 18” of the latch side projects more than 8” from the face of a door or gate, maneuvering clearances for a forward approach must be provided....
-
2010 ADA Standards - Plan Review Tool - Doors
2010 ADA Standards - Plan Review Tool - Doors Click here to view/download the pdf, Page 1 of 2 (258 KB) Click here to view/download the pdf, Page 2 of 2 (264 KB) * * * * * *...
-
California/ADA Plan Review Tool - Door Maneuvering Clearances
California/ADA Plan Review Tool - Door Maneuvering Clearances Click here to view/download the pdf "California/ADA Plan Review Tool - Door Maneuvering Clearances" (250 KB) * * *...
-
Figure 1007.3.2 Golf Club Reach Range Area – Drawing from the U.S. Access Board
-
11B-406.5.10 Diagonal curb ramps
Diagonal curb ramps with flared sides shall have a segment of curb 24 inches (610 mm) long minimum located on each side of the curb ramp and within the marked crossing....
-
D4. Door Clearance
On the pull side of the door, is there at least 18 inches clearance provided to the side of the latch if the door is not automatic or power-operated?...
-
Card Catalogs and Magazine Displays [8.4]
The preferred maximum reach height for card catalogs is 48 inches (recognizing that users may be lifting or manipulating card drawers)....
-
Direct Access Solutions Kit
Hanging up their clothes in a standard closet Adjusting the thermostat to a comfortable temperature Locking and unlocking the security latch Making coffee and reaching...
-
Door and Gate Surfaces [§404.2.10]
Door and Gate Surfaces [§404.2.10] The bottom surface of doors and gates on the push side must be smooth to a height of at least 10”....
-
Transfer Surface Size: Equipment Used by Patients in Supine, Prone, or Side-Lying Position (M301.2.2)
For surfaces on which patients lie down, ANSI/AAMI HE75 recommends that “patients should be able to roll to a side or prone position with minimal need to lift or shift their center of gravity...
-
9.b [§ 4.7.5]
9.b [§ 4.7.5] If the sidewalk at the top of the ramp (“x”) is less than 48 inches wide and the curb ramp you are surveying has flared sides, answer this question....
-
Grab Bars
Grab bars must comply with the reach range requirements of ABAAS, section 308, as explained in "Reach Ranges and Operability Requirements."...
-
§ 1194.25(j)
(j) Products which are freestanding, non-portable, and intended to be used in one location and which have operable controls shall comply with the following:
-
§ 38.123(a)(4)
(4) Faucets and flush controls shall be operable with one hand and shall not require tight grasping, pinching, or twisting of the wrist. The force required to activate controls shall...
-
9.a [§ 4.7.5]
To answer this question you need to determine the slope of the flared sides to make sure it is 10 percent or less....
-
406.5 Location
Curb ramps and the flared sides of curb ramps shall be located so that they do not project into vehicular traffic lanes, parking spaces, or parking access aisles....
-
406.5 Location
Curb ramps and the flared sides of curb ramps shall be located so that they do not project into vehicular traffic lanes, parking spaces, or parking access aisles....
-
Trash, Recycling, and Other Essential Containers
is either 36 inches (914 millimeters) by 48 inches (1,220 millimeters) positioned for a forward approach or 30 inches (760 millimeters) by 60 inches (1,525 millimeters) positioned for a side...
