2. Swinging doors shall provide a net clear opening width of not less than 32 inches (813 mm), measured with the door or doors positioned at an angle of 90 degrees from the closed...
Search Results "ASID: American Society of Interior Designers"
Filters
Commonly Searched Documents
-
1132A.3, Item 2
-
1132A.5.1 General
Maneuvering clearances at interior doors shall provide a minimum length on both sides of the door of at least 42 inches (1067 mm) measured at a right angle to the plane of the door in its...
-
VI. Interior Signs...
[See subsections ...]
-
802 Wheelchair Spaces, Companion Seats, and Designated Aisle Seats
802 Wheelchair Spaces, Companion Seats, and Designated Aisle Seats...
-
The Mayer-Rothschild Foundation
The Foundation is committed to resident-centered relationship-based long-term care, integrating elders and their families into the design, planning and programming of long-term care communities...
-
Common Errors in ADA Design
Common Errors in ADA Design Evan Terry Associates, P.C. concentrates a significant portion of its resources to the study and application of the facilities and program access requirements...
-
Interior Routes
INTERIOR ROUTES Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Carpet pile height 1/2 inch...
-
Interior Routes
INTERIOR ROUTES Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Carpet pile height 1/2 inch...
-
TACTILE SIGN
TACTILE SIGN. A sign containing raised characters and/or symbols and accompanying Braille.
-
Solutions to Enhance Wayfinding (slides 8 -15)
[See subsections ...]
-
At least one percent of all fixed seats in all seating areas must be aisle seats with no armrest, or with a removable or folding armrest
• In addition to wheelchair seating locations, at least one percent of all fixed seats in all seating areas must be aisle seats with no armrest, or with a removable or folding...
-
Exterior Features
Glass garage and barn doors for extra light without extra energy use. Preheated hot water from solar panels for water heater, spa, radiant heating. Greenhouses...
-
Study Questions
Study Questions The purpose of this study was to evaluate a variety of playground surfaces, their ability to meet accessibility requirement, their costs upon initial installation...
-
Selection of Playgrounds
Selection of Playgrounds Newly constructed public playgrounds were selected for participation as test sites in the study. A purposive snowball sampling technique was used to...
-
2.1.1
2.1.1 Clearly state the required installed tolerances for critical construction elements. In most cases, it is best to refer to industry standard tolerances or other industry...
-
2.1.2
2.1.2 State the required tolerances for elements for which there are no industry standards. These may also include elements for which there is an industry tolerance for one aspect of...
-
2.4.1
2.4.1 Based on the methods for measuring compliance, define what remedial actions are acceptable when construction elements exceed tolerances. These may include total replacement,...
-
2.3.2
2.3.2 Define the measurement tools that should be used. The acceptable tools should be selected based on the accuracy required and a reasonable balance between the accuracy of the...
-
2.1.3
2.1.3 State requirements for critical accumulated tolerances. These are instances where individual products and installation procedures may conform to industry standard tolerances...
-
TACTILE SIGN
A sign containing raised characters and/or symbols and accompanying Braille.
-
TACTILE SIGN
A sign containing raised characters and/or symbols and accompanying Braille.
-
Institute for Human Centered Design (IHCD)
The Institute for Human Centered Design (IHCD), founded in Boston in 1978 as Adaptive Environments, is an international non-governmental educational organization (NGO) committed to advancing...
-
Contrast and wayfinding, short-term and long-term
It was a matter of the design team relooking at a problem and coming up with design solutions; [to assure] that many of the decisions that they were making were not made to be barriers to...
-
G. ANSI/AAMI HE 75
In 2009, the Association for the Advancement of Medical Instrumentation issued ANSI/AAMI HE 75, a recommended practice on human factors design principles for medical devices....
