The preferred grab bar height was measured between the floor and the top of the grab bar surface. ...
Search Results "Extended Floor Surface"
Filters
Commonly Searched Documents
-
Front grab bar protocol
-
Standing Supports (M304.3 and M305.3)
provided for the support position used on each side of the standing surface....
-
11B-707.6.3.1 Contrast
Function keys shall contrast visually from background surfaces. Characters and symbols on key surfaces shall contrast visually from key surfaces....
-
11B-707.6.3.1 Contrast
Function keys shall contrast visually from background surfaces. Characters and symbols on key surfaces shall contrast visually from key surfaces....
-
Trail Type
There are three Trails Types: Standard/Terra Trail: A trail that has a surface consisting predominantly of the ground and that is designed and managed to accommodate use on that surface...
-
Detectable Warning
A standardized surface feature built in or applied to walking surfaces or other elements to warn of hazards on a circulation path....
-
106.5.24 Detectable Warning
A standardized surface feature built in or applied to walking surfaces or other elements to warn of hazards on a circulation path....
-
Running Slope of Ramps Deployed to Roadways or Curb-Height Bus Stops
Because of their lower floor and flat entry area, low floor buses can use ramps (instead of lifts) to provide access for passengers with disabilities....
-
Mega Jailhouse Heavy Duty Liquid Soap Dispenser
The dimension of the dispenser is 7-1/8" H by 4-1/2" W by 3-5/8" D and the spout extends 5-1/16"....
-
11B-604.8.3 Coat hooks and shelves
Shelves shall be located 40 inches (1016 mm) minimum and 48 inches (1219 mm) maximum above the finish floor....
-
AUTOMATIC DOOR
The switch that begins the automatic cycle may be a photoelectric device, floor mat or manual switch....
-
1.6.15 Recipient.
institution, organization, or other entity, or any individual in any State, territory, possession, the District of Columbia, or Puerto Rico, to whom federal financial assistance from the DOT is extended...
-
F202.6 Leases
Buildings or facilities leased for 12 months or less shall not be required to comply with F202.6 provided that the lease may not be extended or renewed....
-
1015.3 Viewing Space
The viewing space shall be 32 inches (815 mm) maximum and 51 inches (1295 mm) minimum high above the ground and shall extend the full width of the clear ground space....
-
§8.57(b) Noncompliance with §8.50
If an applicant or a recipient of assistance under a contract which is extended or amended on or after July 11, 1988, fails or refuses to furnish an assurance required under §8.50 or otherwise...
-
12185(d) Deadline
or before the applicable deadlines specified in section 12186(a)(2)(B) of this title will result in a significant reduction in intercity over-the-road bus service, the President shall extend...
-
1015.3 Viewing Space
The viewing space shall be 32 inches (815 mm) maximum and 51 inches (1295 mm) minimum high above the ground and shall extend the full width of the clear ground space....
-
Knee Clearance: Clearance as Measured from Anterior-Most Point - Manual Wheelchair
Hence, to accommodate a particular percentage of users, the side profile of a design element (shown by dotted line) should not extend outside the corresponding shaded area....
-
Knee Clearance: Clearance as Measured from Dorsal Foot Point - Manual Wheelchair
Hence, to accommodate a particular percentage of users, the side profile of a design element (shown by dotted line) should not extend outside the corresponding shaded area....
-
FAQ: Is the Corada Shop secure and PCI Compliant?
This compliance extends to all online stores powered by Shopify....
-
11B-404.2.4 Maneuvering clearances
Maneuvering clearances shall extend the full width of the doorway and the required latch side or hinge side clearance. Exception: Reserved....
-
11B-404.2.4 Maneuvering clearances
Maneuvering clearances shall extend the full width of the doorway and the required latch side or hinge side clearance. Exception: Reserved....
-
11B-411.2.2.1 Visible identification
The identification fixture shall be 80 inches (2032 mm) minimum above the finish floor or ground to the bottom of the fixture....
-
§382.57(c)(6)(iv)(A) Contrast
Function keys must contrast visually from background surfaces. Characters and symbols on key surfaces must contrast visually from key surfaces....
