The minimum percentage of ground floor units required on an accessible route shall equal the percentage of the total buildable area (not restricted-use areas) of the undisturbed site with...
Search Results "Minimum Dimension"
Filters
Commonly Searched Documents
-
TEST NO. 2 – SITE ANALYSIS TEST
-
1131B.2, Item 1
The requirements of 2013 CBC 11B-503 are more stringent in the following respects: 1) a minimum width is prescribed for the vehicle pull-up space; 2) the access aisle must be marked...
-
Reduced scoping for public accommodations, small facilities, and qualified small businesses. (Section-by-Section Analysis)
Disability advocacy groups and individuals strongly objected to exemptions and to significantly reduced scoping, arguing that the 2004 ADAAG represents minimum standards, and that the readily...
-
711.4.1 Through penetrations
space is protected with materials that prevent the passage of flame and hot gases sufficient to ignite cotton waste where subjected to ASTM E 119 time temperature fire conditions under a minimum...
-
Revised and New Standards for Buildings and Facilities
The 2010 ADA Standards for Accessible Design include revised and new minimum requirements for newly and constructed or altered facilities so that they are accessible to and usable by individuals...
-
Number of Accessible Bathrooms
However, in a dwelling unit with more than one bathroom, all bathrooms in the unit must comply with the first set of specifications, or a minimum of one bathroom must comply with the second...
-
11B-606.2 Clear floor space
A knee clearance of 24 inches (610 mm) minimum above the finish floor or ground shall be permitted at lavatories and sinks used primarily by children 6 through 12 years where the rim or...
-
TABLE OF CONTENTS
ACCESSIBLE ELEMENTS AND SPACES: SCOPE AND TECHNICAL REQUIREMENTS 4.1 Minimum Requirements 4.1.1* Application 4.1.2 Accessible Sites and Exterior Facilities: New Construction...
-
General [4.1.6(1)]
ADAAG sets minimum requirements for accessibility in alterations. New construction technical criteria are applied to each element or space altered where technically feasible....
-
208 Parking Spaces
New 4.1.2(5)(b) One in every eight accessible spaces, but not less than one, shall be served by an access aisle 96 in (2440 mm) wide minimum and shall be designated...
-
ASME A18.1 Safety Standard [§410.1]
The ASME A18.1 Standard addresses requirements for runway enclosures, electrical equipment and wiring, structural support, headroom clearance (80” minimum), access ramps, pits, and other...
-
11B-606.2 Clear floor space
A knee clearance of 24 inches (610 mm) minimum above the finish floor or ground shall be permitted at lavatories and sinks used primarily by children 6 through 12 years where the rim or...
-
1009.3 Stairways
In order to be considered part of an accessible means of egress, a stairway between stories shall have a clear width of 48 inches (1219 mm) minimum between handrails and shall either incorporate...
-
11B-213.3.1 Toilet compartments
Full-height partitions and door assemblies can comprise toilet compartments where the minimum required spaces are provided within the compartment. ...
-
11B-233.3.1.2.6.3 Test number two, site analysis test
The minimum percentage of ground floor units required on an accessible route shall equal the percentage of the total buildable area (not restricted-use areas, flood plains or wetlands) of...
-
11B-706.1 General
The technical standards for assistive listening systems describe minimum performance levels for volume, interference, and distortion....
-
11B-606.2 Clear floor space
A knee clearance of 24 inches (610 mm) minimum above the finish floor or ground shall be permitted at lavatories and sinks used primarily by children 6 through 12 years where the rim or...
-
ASTM: ADA Standard Section 105.2.3
Section 105.2.3 of the ADA Standards cover references to the American Society for Testing and Materials (ASTM) standards.
-
Wagner Instruments Chatillon® DFE Digital Force Gauge
Accuracy Accurate to ± 0.25% of Full Scale, ± 1 Least Significant Digit Weight & Dimensions 1.5 lb [0.7 kg], Shipping Weight: 3 lb [1.4 kg]. 7'' [180mm...
-
Allegion aptiQ Multi-Technology Single Gang Reader
Read Range: Proximity--Up to 5" MIFARE--Up to 4" MIFARE DESFire EV1--Up to 2" PIV Credential--Up to 2.5" Weight: 9.1 oz Dimensions...
-
Compliance date
A substantial number of commenters advocated a minimum of 18 months from publication of the final rule to the effective date for application of the standards to new construction, consistent...
-
How is slip resistance measured?
Measuring slip resistance involves the minimum tangential force necessary to initiate sliding of a body over the surface and the body gravity force....
-
Compliance date. (Section-by-Section Analysis)
A substantial number of commenters advocated a minimum of 18 months from publication of the final rule to the effective date for application of the standards to new construction, consistent...
