. ◼ Exceptions: Vertical dispersion shall not be required in assembly areas with 300 or fewer seats if the wheelchair spaces provide viewing angles that are equivalent to, or...
Search Results "General Exception"
-
11B-221.2.3.2 Vertical dispersion
-
Benches
Shoulder alignment generally can be achieved by positioning the back of the bench so that it is 8 inches (200 millimeters) closer to the outdoor recreation access route, trail, or beach...
-
Introduction
., elevator exception, alterations to primacy function areas). ...
-
Doors: ADA Standard Section 604.8.1.2
Section 604.8.1.2 covers the current ADA Standards for wheelchair accessible compartment doors.
-
Designations: ADA Standard Section 216.2
Section 216.2 covers scoping requirements in the current ADA Standards for sign designations.
-
Protrusion Limits: ADA Standard Section 307.2
Section 307.2 covers the current ADA Standards for protrusion limits.
-
Car Dimensions and Doors: ADA Standard Section 408.4.1
Section 408.4.1 covers the current ADA Standards for the car dimensions and doors of limited-use/limited-application elevators.
-
Within a Site: ADA Standard Section 206.2.2
Section 206.2.2 covers the scoping requirements for accessible routes within a site in the most current ADA Standards.
-
Horizontal Dispersion: ADA Standard Section 221.2.3.1
Section 221.2.3.1 covers scoping requirements in the current ADA Standards for horizontal Dispersion in assembly areas.
-
Designated Aisle Seats: ADA Standard Section 221.4
Section 221.4 covers scoping requirements in the current ADA Standards for designated aisle seats in assembly areas.
-
Door and Signal Timing: ADA Standard Section 407.3.4
Section 407.3.4 covers the current ADA Standards for door and signal timing of elevator reopening devices.
-
Toe Clearance: ADA Standard Section 604.8.1.4
Section 604.8.1.4 covers the current ADA Standards for toe clearance at wheelchair accessible compartments.
-
Overlap: ADA Standard Section 604.3.2
Section 604.3.2 covers the current ADA Standards for overlapping clearances in the water closet clear floor space.
-
Grab Bars: ADA Standard Section 1009.5.7
EXCEPTION: Grab bars on transfer systems shall not be required to comply with 609.4....
-
11B-703.4.1 Height above finish floor or ground
Exception: Tactile characters for elevator car controls shall not be required to comply with Section 11B-703.4.1....
-
11B-1009.5.7 Grab bars
Exception: Grab bars on transfer systems shall not be required to comply with Section 11B-609.4....
-
11B-404.3.2 Maneuvering clearance
Exception: Where automatic doors and gates remain open in the power-off condition, compliance with Section 11B-404.2.4 shall not be required....
-
11B-411.2.2.1 Visible identification
Exception: Existing buildings shall be permitted to have a visible identification fixture with a car designation character adjacent to each elevator car entrance centered at 72 inches (1829...
-
11B-705.1.1.2 Dome spacing
Exception: Where installed in a radial pattern, truncated domes shall have a center-to-center spacing of 1.6 inches (41 mm) minimum to 2.4 inches (61 mm) maximum....
-
11B-705.1.2.2.2.1 One entrance/exit point
Exceptions: 1....
-
11B-307.2 Protrusion limits
Exception: Handrails shall be permitted to protrude 4½ inches (114 mm) maximum. Advisory 11B-307.2 Protrusion limits....
-
11B-1009.2.1 Pool lift location
Exceptions: 1. Where the entire pool depth is less than 36 inches (914 mm) or greater than 48 inches (1219 mm), compliance with Section 11B-1009.2.1 shall not be required....
-
11B-407.3.4 Door and signal timing
Exceptions: For cars with in-car lanterns, T shall be permitted to begin when the signal is visible from the point 60 inches (1524 mm) directly in front of the farthest hall call button...
-
11B-206.4.1 Entrances
ETA Editor's Note From DSA's "Summary of 2022 California Building Code Changes for Accessibility in the Triennial Code Cycle": "Code amendment relocates Exceptions 1 and 2 (relating to...