An accessible gate or door shall be provided adjacent to the turnstile or revolving door and shall be so designed as to facilitate the same use pattern....
Search Results "ASID: American Society of Interior Designers"
Filters
Commonly Searched Documents
-
4.13.2 REVOLVING DOORS AND TURNSTILES
-
§ 35.151(a)(1)
(1) Each facility or part of a facility constructed by, on behalf of, or for the use of a public entity shall be designed and constructed in such manner that the facility or part of the...
-
11B-411.2.1.4.1.2 Identification
Identification shall be placed immediately to the left of the control button to which the designation applies....
-
§ 35.172(c)
(c) Where appropriate, the designated agency shall attempt informal resolution of any matter being investigated under this section, and, if resolution is not achieved and a violation is...
-
11B-206.7.2 Wheelchair spaces
accessible route to comply with the wheelchair space dispersion and line-of-sight requirements of Sections 11B-221 _|Assembly Areas|_ and 11B-802 _|Wheelchair Spaces, Companion Seats, and Designated...
-
§ 38.123(a)
(a) If a restroom is provided for the general public, and an accessible restroom is required by §38.111 (a) and (e) of this part, it shall be designed so as to allow a person using a wheelchair...
-
11B-411.2.1.4.1.2 Identification
Identification shall be placed immediately to the left of the control button to which the designation applies....
-
6 [§ 4.7.7]
Detectable warnings are designed to be felt underfoot or with a cane by people who are blind or have low vision, thereby alerting them of hazards– mainly, the transition from a pedestrian-only...
-
STORY
That portion of a building or facility designed for human occupancy included between the upper surface of a floor and upper surface of the floor or roof next above....
-
F244.2.1 Alterations and Additions
EXCEPTION: Where an entity is implementing a transition plan for program accessibility developed pursuant to regulations issued under section 504 of the Rehabilitation Act that designates...
-
Accessible Check-out Aisle Signage
The requirement for identification of check-out aisles has been revised to require that accessible designations be located in the same area as the number, letter, or function identifying...
-
Efforts to maximize benefits
The Electronic Industries Foundation, in its "Resource Guide for Accessible Design of Consumer Electronics", 1996, notes "Today, one factor contributing to market share is the increasing...
-
F245.2.3 Alterations and Additions
EXCEPTION: Where an entity is implementing a transition plan for program accessibility developed pursuant to regulations issued under section 504 of the Rehabilitation Act that designates...
-
1004.1 Clear Floor Space
To optimize space use, designers should carefully consider layout options such as connecting ends of the row and center aisle spaces....
-
Team Player Seating Areas
If designers and operators are designing a field or court that will serve a variety of wheelchair sports, exceeding the minimum requirements will better accommodate participants....
-
308.1 General
The following table provides guidance on reach ranges for children according to age where building elements such as coat hooks, lockers, or operable parts are designed for use primarily...
-
233.3.1.2.2.1 Unit Pads, F233.4.1.2.2.1 Unit Pads
At least 10 percent, but no fewer than one, of the unit pads prepared for the installation of emergency transportable housing units at each group site shall be designed and constructed to...
-
308.1 General
The following table provides guidance on reach ranges for children according to age where building elements such as coat hooks, lockers, or operable parts are designed for use primarily...
-
5.4.5 Transfer Support Position Recommendation for M301 and M302
It addresses angled supports or contoured portions of horizontal supports often provided for ergonomics or equipment design considerations....
-
1004.1 Clear Floor Space
To optimize space use, designers should carefully consider layout options such as connecting ends of the row and center aisle spaces....
-
A.6 - Does Section 508, as implemented by the Access Board’s standards and the FAR, impose the same obligations on agencies and contractors?
Contractors interested in selling EIT to the Federal government are responsible for designing and manufacturing products which conform to the applicable Access Board’s technical provisions...
-
Section 1. Introduction
This section also clarifies that the accessibility guidelines apply only to the design and construction requirements of 24 CFR 100.205, and do not relieve persons participating in a federal...
-
308.1 General
The following table provides guidance on reach ranges for children according to age where building elements such as coat hooks, lockers, or operable parts are designed for use primarily...