OUR MISSION The mission of Independent Living Center of Kern County is to empower people with disabilities to grow creatively, professionally, and personally; and educate the community...
Search Results "Travel Center Facility"
Filters
Commonly Searched Documents
-
Independent Living Center of Kern County - Bakersfield, CA
-
§382.119(b)
information includes but is not limited to the following: information concerning flight safety, procedures for takeoff and landing, flight delays, schedule or aircraft changes that affect the travel...
-
End Note
Good customer service practices that assist people with disabilities will bring repeat business from guests with disabilities, older travelers, and friends and families that accompany this...
-
11B-405.3 Cross slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
Wheelchair
A person whose disability requires use of a wheelchair or mobility device may use a wheelchair or mobility device that meets both parts of this definition anywhere foot travel is permitted...
-
1.1.3 Walk running slope
Measure for overall running slope (the primary direction of travel) by determining elevations at the ends of the walk, noticeable changes in slope, or at a maximum of 20 ft (6 m) intervals...
-
11B-405.3 Cross slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
11B-405.7.4 Change in direction
Ramps that change direction between runs at landings shall have a clear landing 60 inches (1525 mm) minimum by 72 inches (1829 mm) minimum in the direction of downward travel from the upper...
-
11B-405.3 Cross slope
Cross slope is the slope of the surface perpendicular to the direction of travel....
-
11B-405.7.4 Change in direction
Ramps that change direction between runs at landings shall have a clear landing 60 inches (1525 mm) minimum by 72 inches (1829 mm) minimum in the direction of downward travel from the upper...
-
4. Example: Installing Curb Ramps for Program Accessibility
surrounding streets and sidewalks were built pre-ADA and have not since been altered, the town must install curb ramps in compliance with Title II’s program access requirements for pre-ADA facilities...
-
Baseline
in the public right-of-way until new accessibility standards are adopted for these facilities....
-
disABILITY Resource Center (dRC) - Knoxville, TN
Who We Are/What We Do dRC is a Center for Independent Living. (CIL) We are a community-based non-residential program of services....
-
Symmetry Limited Use/Limited Application (LU/LA) Elevator
The Elevation is ideal for applications up to six stops and 25 feet (standard) or 40 feet (with approved variance) of travel....
-
AMUSEMENT ATTRACTION
[DSA-AC] Any facility, or portion of a facility, located within an amusement park or theme park which provides amusement without the use of an amusement device....
-
11B-245.3 Accessible elements required
The accessible portion of the residence extends to those elements used to enter the commercial facility, including the front sidewalk, if any, the door or entryway, and hallways; and those...
-
12.1 Q...How is the individual building test performed for additional stories, to determine if those stories must also be treated as ground floors?
determining whether a non-elevator building has more than one ground floor, the point of measurement for additional ground floors, after the first ground floor has been established, is at the center...
-
7(2)(b)(iv)
In locations where toilets are adjacent to walls or bathtubs, the center line of the fixture is a minimum of 1'6" from the obstacle....
-
11B-503.3.3 Marking
The area within the borderlines shall be marked with hatched lines a maximum of 36 inches (914 mm) on center in a color contrasting with that of the aisle surface....
-
1134A.8, Item 4.3
The knee and toe space shall be centered on the fixture, and shall comply with Section 1138A.2....
-
A4.13.9 Door Hardware
To be effective, they should cover the door width, less approximately 2 in (51 mm), up to a height of 16 in (405 mm) from its bottom edge and be centered across the width of the door....
-
Side Approach
Recommendation: The clear floor space should be centered on the ATM unit....
-
1134A.8, Item 4.3
The knee and toe space shall be centered on the fixture, and shall comply with Section 1138A.2....
