ADA, TAS, and ANSI Compliant: When the washfountain is mounted at the standard 34" adult rim height it is designed to comply with applicable ADA, TAS, and ANSI Z124.3 and Z124.6 accessibility...
Search Results "ANSI: American National Standards Institute"
Filters
Commonly Searched Documents
-
Willoughby Industries WWF-3603 Three Station Half Round 36" Stainless Steel Deep Bowl Washfountain
-
Willoughby Industries WWF-5403/5404 AquaFount® Three and Four Station Half Round 54" Solid Surface Deep Bowl Washfountain
ADA, TAS, and ANSI Compliant: When the washfountain is mounted at the standard 34" adult rim height, it is designed to comply with applicable ADA, TAS, and ANSI Z124.3 and Z124.6 accessibility...
-
Willoughby Industries WWF-4206 Six Station Full Round 42" Stainless Steel Deep Bowl Washfountain
ADA, TAS, and ANSI Compliant: At the standard 34" adult rim height, two (2) stations are designed to comply with applicable ADA, TAS, and ANSI Z124.3 and Z124.6 accessibility guidelines...
-
Willoughby Industries WAF-3606 AquaFount® Six Station Full Round 36" Solid Surface Deep Bowl Washfountain
ADA, TAS, and ANSI Compliant: At the standard 34" adult rim height, one (1) station is designed to comply with all applicable ADA, TAS, and ANSI Z124.3 and Z124.6 accessibility guidelines...
-
Willoughby Industries WBL-2320 Ligature-resistant Behavioral Healthcare Lavatory System
ADA,TAS,UFAS and ANSI Compliant: When the lavatory is mounted at the standard adult rim height it is designed to comply with all applicable ADA,TAS,UFAS and ANSI Z124.3 and Z124.6 accessibility...
-
Section 5.0 Dissemination Activities
The intermediate-term goal is to provide knowledge to improve existing standards....
-
After January 26, 1992
Any state or local government facility that was altered after January 26,1992 was required to be altered in compliance with the ADA Standards or UFAS....
-
Rockwood Manufacturing Company 620 UL Listed 160˚ Door Viewer For Doors 1-3/8" to 2"
ANSI A156.16: L03222, L03172 Most of Rockwood's products are available in a wide variety of architectural finishes....
-
How is slip resistance measured?
Adding sand to the icy surface will increase its coefficient of friction and allow for a more standard gait....
-
M101.5 Dimensions
The MDE Standards are based on adult dimensions and anthropometrics. Dimensions that are not stated as “maximum” or “minimum” are absolute....
-
407.4.6.3 Keypads
Car control keypads shall be in a standard telephone keypad arrangement and shall comply with 407.4.7.2....
-
i.
"Suspicious Minds" Exhibit ramp leading to the exhibits; and See Standards § 4.8.5(3)....
-
407.4.6.3 Keypads
Car control keypads shall be in a standard telephone keypad arrangement and shall comply with 407.4.7.2....
-
E202.1 General
ICT shall be exempt from compliance with the Revised 508 Standards to the extent specified by E202....
-
E202.4 Federal Contracts
ICT acquired by a contractor incidental to a contract shall not be required to conform to the Revised 508 Standards....
-
E201.1 Scope
ICT that is procured, developed, maintained, or used by agencies shall conform to the Revised 508 Standards....
-
225(d)(1)(B)
(B) establish minimum standards that shall be met in carrying out subsection (c) of this section;...
-
Station platforms
(DOT ADA Standard 810.5.3.)...
-
M18
[ADA Standards § 4.16.5] Yes No...
-
11B-705.1.1.3.1
Detectable warning surfaces shall be yellow and approximate FS 33538 of Federal Standard 595C....
-
§40.3(b)(3)
(3) The alteration of an existing building, or of such portions thereof, to which application of the standards is not structurally feasible....
-
ADMINISTRATIVE AUTHORITY
A governmental agency that adopts or enforces regulations and standards for the design, construction, or alteration of buildings and facilities....
-
§100.201a(b)
(b) The addresses of organizations from which the referenced standards can be obtained appear below:...
-
Cal-Royal NM Series Extra Heavy Duty Mortise Lockset
Listed "A" Label (3 hour), for use on fire doors; single or pairs ANSI - Lock body conforms to Federal Specification Type 86; and to all dimensional and operational performances of ANSI...
