Openings in floor or ground surfaces shall not allow passage of a sphere more than ½ inch (13 mm) diameter except as allowed in 407.4.3, 409.4.3, 410.4, 810.5.3 and 810.10....
Search Results "Teeing Ground"
2010 ADA Definition
Teeing Ground: In golf, the starting place for the hole to be played.
Filters
Commonly Searched Documents
-
302.3 Openings
-
1011.2.4 Openings
This section requires openings in the clear ground space such as drainage grates to not allow passage of a sphere more than 1/2 inch in diameter....
-
11B-233.3.1.2.3 Ground floors above grade
ETA Editor's Note This section of the 2019 California Building Code was amended by the Division of the State Architect. The requirements in this section were previously found in...
-
5.1.6 Clear Floor or Ground Space
A clear floor or ground space at least 36 inches (915 mm) by 48 inches (1220 mm) shall be provided parallel to the entrance to the camp shelter....
-
11B-503.4 Floor and ground surfaces
Vehicle pull-up spaces and access aisles serving them shall comply with Section 11B-302. Access aisles shall be at the same level as the vehicle pull-up space they serve. Changes in...
-
1011.2.4 Openings
Openings in the clear ground space surface shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1011.2.4 Openings. ...
-
1011.2.4 Openings
Openings in the clear ground space surface shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1011.2.4 Openings....
-
RecGrass Synthetic Grass Ground Surface System Section
Requires the Premium User plan or above. (Login or upgrade your account!) -
1002.6.1 Clear Floor or Ground Space
1002.6.1 Clear Floor or Ground Space. A clear floor or ground space complying with 305 shall be provided in the load and unload area adjacent to the transfer device....
-
3. Ground and floor surface treatments
Ground and floor surface treatments 4.5 Accessible routes, and spaces, including floors, walks, ramps, stairs, and curb ramps....
-
4.33.4 Surfaces
The ground or floor at wheelchair locations shall be level and shall comply with 4.5....
-
4.33.4 SURFACES
The ground or floor at wheelchair locations shall be level and shall comply with 4.5....
-
1013.2.1 Size
The clear ground space shall be 48 inches (1220 mm) wide minimum....
-
1013.2.1 Size
The clear ground space shall be 48 inches (1220 mm) wide minimum....
-
11B-302.3 Openings
Openings in floor or ground surfaces shall not allow passage of a sphere more than ½ inch (12.7 mm) diameter except as allowed in Sections 11B-407.4.3 _|Platform to Hoistway Clearance|_,...
-
Clear Floor Space
The minimum unobstructed floor or ground space required to accommodate a single, stationary wheelchair and occupant....
-
Slip Resistance
Standard practices for minimizing floor or ground slipperiness will likely satisfy compliance with the standards as slip resistance is important not just for accessibility but for general...
-
Technical Bulletin: Ground and Floor Surfaces
UNITED STATES ACCESS BOARD A FEDERAL AGENCY COMMITTED TO ACCESSIBLE DESIGN Technical Bulletin: Ground and Floor Surfaces...
-
11B-404.2.4.4 Floor or ground surface
Floor or ground surface within required maneuvering clearances shall comply with Section 11B-302....
-
Load and Unload Areas
Load and Unload Areas The floor or ground surface in the load and unload areas must have a slope not steeper than 1:48 and be stable, firm, and slip resistant....
-
Miracle Sealant Slip-Resistant Flooring Treatment
511 Anti-Slip is a professional grade penetrating sealer designed for the slip-protection of all ceramic tile, porcelain tile, polished marble, polished granite, concrete, masonry...
-
Openings [§302.3]
Openings [§302.3] Openings in ground and floor surfaces, such as grates, are limited in width to prevent passage of a ½” diameter sphere....
-
4.4.6 Surface
The surface of the clear floor or ground space for benches shall be firm and stable. The type of surface should be appropriate to the setting and level of development....
-
302.3 Openings
Openings in floor or ground surfaces shall not allow passage of a sphere more than 1/2 inch (13 mm) diameter except as allowed in 407.4.3, 409.4.3, 410.4, 810.5.3 and 810.10....
