Special care is needed when measuring the clear opening of a doorway. To measure the clear opening of a standard hinged door, open the door to 90 degrees....
Search Results "Side-Opening Door"
Filters
Commonly Searched Documents
-
Measuring Door Openings
-
Cal-Royal 700 Series Hydraulic Door Closers
Hydraulic door closer dual valve, closing and latching speed controlled by two separate regulating valves....
-
CRL PR40 Series Adjustable Spring Power Surface Mounted Door Closers
08 7100 CRL DC50 Series ANSI Grade 1 Surface Mounted Door Closers Applicable for Doors Ranging From 26" to 54" Wide and 33 to 264 Pounds Dual Valve Closing and Latching Speed Control...
-
Cal-Royal Hydraulic Door Closers 400 Series
Standard Duty Commercial Hydraulic Door Closer Precision Engineering for New Construction Meets And Exceeds ANSI Standard 156.4 Grade 2 Sized Door Closer, Sizes 2, 3 And 4 For All...
-
DORMA BTS75V SERIES DOOR CLOSER
Floor-Concealed Door Closer The BTS75V Series of floor-concealed door closers offer adaptability to almost any installation....
-
BEA Inc. LZR Microscan Installation Video
The LZR-microscan is the next generation sensor system for swing door safety. ...
-
Revolving Doors or Turnstiles
A commenter advised that no revolving doors or turnstiles should be permitted on an accessible route. Response....
-
T302.3 Openings
Openings in walking surfaces shall not allow the passage of a sphere more than 5/8 inch (16 mm) in diameter....
-
Doors at Entrances to Businesses
However, some older doors are less than 36 inches wide and may not provide enough width (32 inch clear width when fully opened). Door openings can sometimes be enlarged....
-
Hager Companies 5400 Series - Standard Duty Surface Door Closer
The closers are non-handed to permit installation on doors of either hand. These closers have fixed spring sizes....
-
1010.1.6 Thresholds
or landing for other doors....
-
Sides of Curb Ramps
Section 406.3 addresses the sides of curb ramps and specifies that side flares, where provided, have a slope of 1:10 maximum....
-
11B-404.2.8.1 Door closers and gate closers
Door closers and gate closers shall be adjusted so that from an open position of 90 degrees, the time required to move the door to a position of 12 degrees from the latch is 5 seconds minimum...
-
11B-404.2.8.1 Door closers and gate closers
Door closers and gate closers shall be adjusted so that from an open position of 90 degrees, the time required to move the door to a position of 12 degrees from the latch is 5 seconds minimum...
-
Maneuvering Clearances at Doors [4.13.6]
Maneuvering Clearances at Doors [4.13.6] Pull-side clearance beyond the door swing provides space for a forward reach to door hardware....
-
Doors and Gates in Series [§404.2.6]
Doors and Gates in Series [§404.2.6] At hinged or pivoted doors or gates in series, a separation is required that is at least 48” plus the width of doors or gates swinging into the space...
-
11B-404.2.8.1 Door closers and gate closers
Door closers and gate closers shall be adjusted so that from an open position of 90 degrees, the time required to move the door to a position of 12 degrees from the latch is 5 seconds minimum...
-
American Specialties Surface Mounted Bottle Opener 0711-B
Surface Mounted Bottle Opener shall be fabricated of alloy 18-8 stainless steel, type 304, No16 gauge of one piece construction....
-
11B-404.3 Automatic and power-assisted doors and gates
Automatic and power-assisted doors are often used by designers to provide accessibility when door closer pressure would exceed the allowable opening force for interior or exterior doors....
-
11B-404.3 Automatic and power-assisted doors and gates
Automatic and power-assisted doors are often used by designers to provide accessibility when door closer pressure would exceed the allowable opening force for interior or exterior doors....
-
1132A.1 Primary entry doors and required exit doors
The width and height of primary entry doors and all required exit doors shall comply with Section 1126A.1....
-
1132A.1 Primary entry doors and required exit doors
The width and height of primary entry doors and all required exit doors shall comply with Section 1126A.1....
-
1132A.1 Primary entry doors and required exit doors
1132A.1 Primary entry doors and required exit doors. The width and height of primary entry doors and all required exit doors shall comply with Section 1126A.1....
-
Hager Companies 5300 Series - Heavy Duty Surface Door Closer
These design features make this closer the ideal choice for doors with a maximum weight of 250 lbs....
