407.12.1.1 Vertical Plane for Side Reach (Section-by-Section Analysis) This section proposes that, where a side approach is provided, the vertical reference plane must have a minimum length...
Search Results "Segment Length"
Filters
Commonly Searched Documents
-
407.12.1.1 Vertical Plane for Side Reach (Section-by-Section Analysis)
-
406.6 Diagonal Curb Ramps
Diagonal curb ramps with flared sides shall have a segment of curb 24 inches (610 mm) long minimum located on each side of the curb ramp and within the marked crossing....
-
Data Deficiencies
Data Deficiencies Advocates on the committee, representing the interests of people with disabilities, strongly stated that a 17” height is essential to accommodate the largest segment...
-
4. Summary of Practice
Figure 1 provides PRI value descriptors from research conducted at the Human Engineering Research Laboratories for simulated and community surfaces made of wood, segmental paving units,...
-
1132A.5.1 General
The floor or landing on the dwelling unit side of the primary entry door and any required exit door shall have a minimum length of not less than 44 inches (1118 mm)....
-
Parallel Approach: ADA Standard Section 904.4.1
A clear floor or ground space complying with 305 shall be positioned for a parallel approach adjacent to the 36 inch (915 mm) minimum length of counter. , EXCEPTION: Where the provided...
-
11B-405.9.2 Curb or barrier
To prevent wheel entrapment, the curb or barrier shall provide a continuous and uninterrupted barrier along the length of the ramp....
-
Minimum Rear Wall Required.
It appears that this comment references the 2010 ADA Standards for Accessible Design for minimum bench length (42") but uses the CA - 2013 minimum bench length (48") to develop the minimum...
-
Recommendations
Recommendations Based on the data in Table 1 and the observations above, we recommend: a minimum flat surface of 40 in. length for platforms accommodating wheeled mobility devices...
-
§ 38.25(c) Door height
For vehicles in excess of 22 feet in length, the overhead clearance between the top of the door opening and the raised lift platform, or highest point of a ramp, shall be a minimum of 68...
-
Rise
The maximum length of a run is determined by the rise (30 inches maximum) and the slope: Max. Rise Slope Max. Length Max. Rise Slope Max....
-
R306.3.2 Pedestrian Activated Signals
At roundabouts with multi-lane pedestrian street crossings, a pedestrian activated signal complying with R209 shall be provided for each multi-lane segment of each pedestrian street crossing...
-
406.6 Diagonal Curb Ramps
Diagonal curb ramps with flared sides shall have a segment of curb 24 inches (610 mm) long minimum located on each side of the curb ramp and within the marked crossing....
-
4.7.10 DIAGONAL CURB RAMPS
If diagonal curb ramps have flared sides, they shall also have at least a 24 in (610 mm) long segment of straight curb located on each side of the curb ramp and within the marked crossing...
-
Standing Supports (M304.3 and M305.3)
Standing Supports (scales serving both wheelchair and standing users) • Sub-Committee Recommendation: Standing Supports - Length The length of the standing supports to be 32” minimum...
-
Sales and Service Counters: ADA Standard Section 904.4
shall be permitted to have a portion which is 24 inches (610 mm) long minimum complying with 904.4.1 provided that the required clear floor or ground space is centered on the accessible length...
-
Landings: ADA Standard Section 406.4
Section 406.4 covers the current ADA Standards for curb ramp landings.
-
Boarding Piers at Boat Launch Ramps
In addition, gangways connecting floating boarding piers may exceed the maximum slope specified in the guidelines, if the total length of the gangway is at least 30 feet....
-
221.2.3.1 Horizontal Dispersion
shall not be required in assembly areas with 300 or fewer seats if the companion seats required by 221.3 and wheelchair spaces are located within the 2nd or 3rd quartile of the total row length...
-
221.2.3.1 Horizontal Dispersion
shall not be required in assembly areas with 300 or fewer seats if the companion seats required by 221.3 and wheelchair spaces are located within the 2nd or 3rd quartile of the total row length...
-
505.6 Gripping Surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
11B-809.8.3 Door maneuvering clearance.
At the dwelling unit side of the primary entry doors, secondary exterior doors, and required exit doors maneuvering clearances shall be 44 inches (1118 mm) minimum in length measured...
-
Healthcare Stories - Carol Gill and Larry Voss Part 3 of 6
Requires the Registered User plan or above. Login! -
Healthcare Stories - Carol Gill and Larry Voss Part 5 of 6
Requires the Registered User plan or above. Login!