Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or...
Search Results "Horizontal Dispersion"
Filters
Commonly Searched Documents
-
11B-903.6 Structural strength
-
F221.2.1.3 Other Boxes
Additionally, because the wheelchair spaces must also meet the dispersion requirements of F221.2.3, the boxes containing these wheelchair spaces cannot all be located in one area unless...
-
221.2.1.3 Other Boxes
Additionally, because the wheelchair spaces must also meet the dispersion requirements of 221.2.3, the boxes containing these wheelchair spaces cannot all be located in one area unless an...
-
221.2.1.3 Other Boxes
Additionally, because the wheelchair spaces must also meet the dispersion requirements of 221.2.3, the boxes containing these wheelchair spaces cannot all be located in one area unless an...
-
HANDRAIL
A horizontal or sloping rail intended for grasping by the hand for guidance or support....
-
HANDRAIL
A horizontal or sloping rail intended for grasping by the hand for guidance or support....
-
HANDRAIL
A horizontal or sloping rail intended for grasping by the hand for guidance or support....
-
Slope Ratio
Slope Ratio—A ratio of vertical distance to horizontal distance or rise to run....
-
Attachment H: Modifications to Altered Facilities
Attachment H: Modifications to Altered Facilities
-
11B-505.10.3 Bottom extension at stairs
At the bottom of a stair flight, handrails shall extend at the slope of the stair flight for a horizontal distance equal to one tread depth beyond the last riser nosing....
-
11B-407.3.1 Type
Elevator doors shall be the horizontal sliding type. Car gates shall be prohibited....
-
407.3.1 Type
Elevator doors shall be the horizontal sliding type. Car gates shall be prohibited....
-
407.3.1 Type
Elevator doors shall be the horizontal sliding type. Car gates shall be prohibited....
-
11B-407.3.1 Type
Elevator doors shall be the horizontal sliding type. Car gates shall be prohibited....
-
11B-407.3.1 Type
Elevator doors shall be the horizontal sliding type. Car gates shall be prohibited....
-
Back Support: ADA Standard Section 903.4
Back support shall be 2½ inches (64 mm) maximum from the rear edge of the seat measured horizontally. Advisory 903.4 Back Support....
-
F105.2.5 NFPA
UL 1971 specifies intensity dispersion requirements for visible alarms....
-
11B-221.2.1.3 Other boxes
Additionally, because the wheelchair spaces must also meet the dispersion requirements of 221.2.3, the boxes containing these wheelchair spaces cannot all be located in one area unless an...
-
105.2.5 NFPA
UL 1971 specifies intensity dispersion requirements for visible alarms....
-
105.2.5 NFPA
UL 1971 specifies intensity dispersion requirements for visible alarms....
-
11B-221.2.1.3 Other boxes
Additionally, because the wheelchair spaces must also meet the dispersion requirements of 221.2.3, the boxes containing these wheelchair spaces cannot all be located in one area unless an...
-
11B-221.2.1.3 Other boxes
Additionally, because the wheelchair spaces must also meet the dispersion requirements of Section 11B-221.2.3, the boxes containing these wheelchair spaces cannot all be located in one area...
-
Bobrick Swing-Up Grab Bar B-4998
., satin-finish stainless steel Swing-up grab bar is manually raised for approach or departure and lowered to horizontal position for support; once grab bar is raised to the full upright...
-
609.4 Position of Grab Bars
Grab bars shall be installed in a horizontal position, 33 inches (840 mm) minimum and 36 inches (915 mm) maximum above the finish floor measured to the top of the gripping surface, except...
