404.2.10 Door and Gate Surfaces....
Search Results "Floor Surface"
Filters
Commonly Searched Documents
-
404.2.10 Door and Gate Surfaces
-
Surface and Slope [1012.4 and 1012.5]
The surface of parking spaces and pull-up spaces for RVs must be firm and stable....
-
10.3.1(19)
Gates which must be pushed open by wheelchair or mobility aid users shall have a smooth continuous surface extending from 2 inches above the floor to 27 inches above the floor....
-
404.2.10 Door and Gate Surfaces
Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
Dining Surface and Work Surface
Commenters expressed concern about use of the terms "dining surfaces" and "work surfaces" and urged the Board to include definitions of the terms in the final rule....
-
404.2.10 Door and Gate Surfaces
Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
Must accessible surfaces be paved?
Concrete, asphalt, and other paved surfaces are more reliably compliant, but other materials, such as wood, and construction methods can be used to provide firm and stable surfaces. ...
-
Exterior Surfaces
However, some natural surfaces, such as compacted earth, soil treated with consolidants, or materials stabilized and retained by permanent or temporary geotextiles (mesh), gridforms, or...
-
Surfaces of Trails
Trail surfaces must be firm and stable....
-
1017.2 Surface
This section requires the surface of trails, passing spaces, and resting intervals to be firm and stable. A firm trail surface resists deformation by indentations....
-
§ 38.83(b)(6) Platform surface
(6) Platform surface. The lift platform surface shall be free of any protrusions over 1/4 inch high and shall be slip resistant....
-
ADA Gap Tool
ADA Gap Tool This handy tool was developed by Evan Terry Associates to assist its surveyors in measuring gaps in ground or floor surfaces....
-
11B-405.4 Floor or ground surfaces
Floor or ground surfaces of ramp runs shall comply with Section 11B-302. Changes in level other than the running slope and cross slope are not permitted on ramp runs....
-
11B-405.4 Floor or ground surfaces
Floor or ground surfaces of ramp runs shall comply with Section 11B-302. Changes in level other than the running slope and cross slope are not permitted on ramp runs....
-
11B-405.4 Floor or ground surfaces
Floor or ground surfaces of ramp runs shall comply with Section 11B-302. Changes in level other than the running slope and cross slope are not permitted on ramp runs....
-
Reese Enterprises, Inc. PERFEC MATv * Aluminum Hinge
They offer solid footing and abrasive surfaces, and they are available in a variety of materials and colors to complement any entry area....
-
Surface and Slope [1015.5 and 1015.6]
The surface of clear ground spaces and turning spaces must be firm and stable....
-
§ 38.159(b)(6) Platform surface
(6) Platform surface. The platform surface shall be free of any protrusions of 1/4 inch (6.5 mm) high and shall be slip resistant....
-
11B-411.2.1.6 Identification of floors served
In buildings with two or more elevator banks, each serving a different group of specific floors, hall call consoles located on floors with a building entry, including parking and transfer...
-
Measuring Surface Firmness and Stability
The rotational penetrometer (RP) is a precision surface-indenter measuring tool for evaluating the firmness and stability of ground and floor surfaces (figure 1). ...
-
Inpro Corporation JointMaster® DR Series Seal Expansion Joint Systems
The DR series compression seal stands up to any challenge due to an installation process that is not weather sensitive. Features & Benefits: Heavy pedestrian / Heavy...
-
Surfaces for Outdoor Recreation Access Routes
Firm and stable surfaces prevent assistive devices from sinking into the surface....
-
11B-810.5.3 Platform and vehicle floor coordination
compliance is not operationally or structurally feasible in light rail, commuter rail, or intercity rail systems: [ADA Title II - Public Transportation] 810.5.3 Platform and Vehicle Floor...
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
