Search Results "Braille Position"

• State and Local Documents > Codes and Standards > 2025 California Standards
  11B-220.1.2 Two automatic teller machines or fare machines

  Where two automatic teller machines or fare machines are provided at a location, one shall comply with Sections 11B-707.2 through 11B-707.8 and one shall comply with Sections...

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.9.1 Standing Supports In Reference To Mammography Equipment

  To be useful, positioning supports must be shaped for grasping, positioned within reach range of all users, and be 12 inches long minimum when located on the moving C-arm or 18 inches long...

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.1 Transfer Surface Height

  5.1 Transfer Surface Height

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.1.4 Transfer Surface Height Measurement

  5.1.4 Transfer Surface Height Measurement. The transfer surface height should be measured from the floor to the highest point on the seat in an uncompressed state, inclusive of...

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M305.3.1.1 Horizontal Position

  The length of gripping surfaces on horizontal standing supports shall be 4 inches (100 mm) minimum except for diagnostic equipment containing a wheelchair space which shall comply...

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M305.3.2.1 Horizontal Position

  The height of the top of the gripping surface on horizontal standing supports shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum above the standing surface.

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M305.2.2 Length

  The length of transfer supports shall comply with M305.2.2.1 or M305.2.2.2.

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.5.1 Armrest Provision for M302

  5.5.1 Armrest Provision for M302 Description: Diagnostic equipment used by patients in a seated position such as exam chairs typically have armrests....

• Federal Documents > Technical Assistance > ADA Best Practices Tool Kit for State and Local Governments
  a. Problem: Images Without Text Equivalents

  Two commonly used technologies are screen readers and refreshable Braille displays....

• Products and Additional Resources > Products
  Seton ADA Braille Sign - Emergency Exit Only 89424
  

  ADA compliant signs clearly indicate exits and identify important emergency related information One-piece, injection molded signs are constructed with a non-glare, matte...

• Rulemaking Process Documents > NPRMS > 36 CFR Part 1195 Proposed Accessibility Standards for Medical Diagnostic Equipment NPRM - Preamble
  Armrests (M302.3.2)

  M302.3.2 would require armrests to be provided on diagnostic equipment used by patients in a seated position....

• Webinars, Videos, and Training > How to Measure
  703.4.1 Raised Letter and Braille Signage Height
  

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M305.2.8 Fittings

  Transfer supports shall not rotate within their fittings when in place for transfer.

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M305.2.7 Clearance

  Clearance between the transfer support gripping surface and adjacent surfaces or obstructions shall be 1 ½ inches (38 mm) minimum.

• Federal Documents > Preamble to Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment - Preamble
  M305.2.7 Clearance (Section-by-Section Analysis)

  In the MDE NPRM, the Access Board did not provide any specific requirements for clearances around the transfer support. However, in the preamble to the MDE NPRM the Access Board...

• Rulemaking Process Documents > NPRMS > 36 CFR Part 1195 Proposed Accessibility Standards for Medical Diagnostic Equipment NPRM
  M305.2.3 Fittings

  Transfer supports shall not rotate within their fittings.

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.2.1.1 Transfer Surface Width Recommendations for M301

  Transfer Surface Width Recommendations for M301 The Committee recommends a transfer surface of 28 inches minimum width for equipment used by patients in a supine, side-lying, or prone position...

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M302.2.2 Sunset

  The low transfer position height, Item A of M302.2.1, shall cease to have effect on [Insert date 5 years after date of publication in the Federal Register]. [sic]...

• Products and Additional Resources > Products
  Innerface ARQ Interior Sign Frame System
  

  The extruded aluminum frame accepts a variety of insert materials, and if required, an ADA compliant clear non-glare cover protects your graphics and allows for raised characters and Braille...

• Products and Additional Resources > Products
  Innerface Clearview Interior Signage
  

  Modules are available in sizes to meet any signage and wayfinding need and all are compatible with ADA compliant raised characters and Braille....

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M305.3.1.3 Vertical Position

  The length of the gripping surface on vertical standing supports shall be 18 inches (455 mm) minimum.

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M305.3.2.2 Vertical Position

  The height of the lowest end of the gripping surface on vertical standing supports shall be 34 inches (865 mm) minimum and 37 inches (940 mm) maximum above the standing surface.

• Rulemaking Process Documents > NPRMS > 36 CFR Part 1195 Proposed Accessibility Standards for Medical Diagnostic Equipment NPRM
  M305.3.2 Vertical Position

  Where the support is vertical, it shall be 18 inches (455 mm) minimum in length and the bottom end of the support shall be 34 inches (865 mm) high minimum and 37 inches (940 mm) high...

• Federal Documents > Technical Assistance > ADAAG Manual
  Identification [4.3.11.5]

  Requirements for tactile (raised and Braille) signage apply to exits and other designations of "permanent rooms and spaces."...