to swing door completely clear of the opening when door is opened 95° Consult factory for hinges available to clear 90° Equipped with four Stanley permanently lubricated non-detachable...
Search Results "Swing Clear Hinge"
Filters
Commonly Searched Documents
-
Stanley FBB 266 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
-
Stanley FBB 268 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
to swing door completely clear of the opening when door is opened 95° Consult factory for hinges available to clear 90° Equipped with four Stanley permanently lubricated non-detachable...
-
Stanley FBB 264 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
to swing door completely clear of the opening when door is opened 95° Consult factory for hinges available to clear 90° Equipped with four Stanley permanently lubricated non-detachable...
-
Stanley FBB 269 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
to swing door completely clear of the opening when door is opened 95° Consult factory for hinges available to clear 90° Equipped with four Stanley permanently lubricated non-detachable...
-
Stanley F248 Standard Weight Plain Bearing “Swing Clear” Full Mortise Offset Door Hinge
flush tips and pins Ideal for remodeling or new construction Available for full mortise application on square edge doors only Designed to replace existing 3 1/2" (89mm) or 4" (102mm) hinges...
-
Door Swing: ADA Standard Section 803.3
Doors shall not swing into the room unless a clear floor or ground space complying with 305.3 is provided beyond the arc of the door swing....
-
Stanley FBB 248 Standard Weight Ball Bearing “Swing Clear” Full Mortise Offset Door Hinge
construction Specify FBB248 and STSFBB248 for full mortise application on square edge doors Specify FBB258 and STSFBB258 for full mortise application on bevel edge doors Designed to swing...
-
Inclusion Solutions Offset Door Hinge
These special hinges are designed to swing the door clear of the opening, adding about 2" additional clearance for wheelchairs and walkers....
-
§ 36.304(b)(9)
(9) Installing offset hinges to widen doorways;...
-
Sec.36.304(b)(9)
(9) Installing offset hinges to widen doorways;...
-
Spring Hinges: ADA Standard Section 404.2.8.2
Section 404.2.8.2 covers the current ADA Standards for door and gate spring hinges.
-
ElectionSource Voter Accessibility Expansion Door Hinge
Easy to install, uses same screws and hole positions as standard door hinges!...
-
11B-404.2.4.1 Swinging doors and gates
Swinging doors and gates shall have maneuvering clearances complying with Table 11B-404.2.4.1....
-
11B-404.2.8.2 Spring hinges
Door and gate spring hinges shall be adjusted so that from the open position of 70 degrees, the door or gate shall move to the closed position in 1.5 seconds minimum....
-
11B-603.2.3 Door swing
Doors shall not swing into the clear floor space or clearance required for any fixture....
-
11B-803.3 Door swing
Doors shall not swing into the room unless a turning space complying with Section 11B-304.3 is provided beyond the arc of the door swing....
-
3(2)
Note A 34-inch door, hung in the standard manner, provides an acceptable nominal 32-inch clear opening....
-
11B-813.2.10 Door swing
Where a clear floor space complying with Section 11B-305.3 is provided within the room beyond the arc of the door swing, doors shall be permitted to swing into the clear floor space, clearance...
-
Doors at Entrances to Businesses
However, some older doors are less than 36 inches wide and may not provide enough width (32 inch clear width when fully opened). Door openings can sometimes be enlarged....
-
11B-304.4 Door swing
Doors shall be permitted to swing into turning spaces....
-
Minimum Clear Opening
A few commenters advocated a wider clear opening. U.S....
-
404.2.8.2 Spring Hinges
404.2.8.2 Spring Hinges....
-
11B-404.2.4.1 Swinging doors and gates
Beyond hinge side. 4. Add 4 inches (102 mm) if closer is provided. 5. Add 6 inches (152 mm) at exterior side of exterior doors....
-
404.2.8.2 Spring Hinges
Door and gate spring hinges shall be adjusted so that from the open position of 70 degrees, the door or gate shall move to the closed position in 1.5 seconds minimum....
