Electric vehicle charging stations (EVCS) shall comply with Section 11B-812 as required by Section 11B-228.3. Where vehicle spaces and access aisles are marked with lines,...
Search Results "Conversion Technique"
Filters
Commonly Searched Documents
-
11B-812.1 General
-
4.1.2 Surface Design of Examination Tables and Chairs
This allows patients to choose the transfer location and technique that best meets their individual needs....
-
Wall-Mounted Objects
Proper cane and service animal techniques allow people to walk along a corridor or path without bumping into walls....
-
A4.4.1 GENERAL
The two principal cane techniques are the touch technique, where the cane arcs from side to side and touches points outside both shoulders; and the diagonal technique, where the cane is...
-
A4.4.1 General
The two principal cane techniques are the touch technique, where the cane arcs from side to side and touches points outside both shoulders; and the diagonal technique, where the cane is...
-
H. How Can You Tell if a Curb Ramp is Accessible?
The best way to determine if a curb ramp is accessible is to survey it to determine the extent to which it complies with ADA accessibility requirements. To assist you, the next...
-
Taking Measurements
[See subsections ...]
-
Initial Measures and Transfer Setup
Wheelchair measurements were completed without the person seated in their wheelchair. The device seat to floor height was measured as the linear distance between the front of the...
-
2. Using the Tape Measure
2. Using the Tape Measure A metal tape measure is needed to measure the length, width, height, and depth of various elements. When measuring long distances, pull the tape tight to...
-
Take Good Measurements
Take Good Measurements When in doubt write it down. It’s better to have too much information than not enough. Even if something is in compliance it’s helpful to have exact...
-
Unified Facilities Guide Specifications
Unified Facilities Guide Specifications In Section 02752, Portland Cement Concrete Pavement for Roads and Site Facilities, published by the National Institute of Building...
-
2.3.1
2.3.1 Define the measurement protocols to be used to check for compliance with the tolerances and standards. This may include where measurements are made, how many should be made,...
-
Common Questions (Protruding Objects)
Common Questions
-
Suggestions by Jean Tessmer
Suggestions by Jean Tessmer As published in Concrete Technology Today, April 2001, Jean Tessmer, accessibility consultant for Space Options, suggested that ramp slopes be measured...
-
Location Above Detectable Elements
Objects located above elements that are within can sweep can protrude 4” maximum from the leading edge of such elements provided that any required reach or clear floor space is not...
-
502.1 General
Car and van parking spaces shall comply with 502. Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline...
-
11B-502.1 General
Car and van parking spaces shall comply with Section 11B-502. Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from...
-
How to Measure Access Aisles
In the final rule, the Board has clarified how parking spaces and access aisles are to be measured. Where parking spaces are marked with lines, the width of parking spaces and...
-
Q6.) How important is the method of measurement in considering the tolerances allowable in finished construction?
A6.) Methods of measurement are critical in determining both compliance and allowable tolerances. The industry’s standards are usually very clear about how to make their...
-
502.1 General
Car and van parking spaces shall comply with 502. Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline...
-
B. Measuring Clear Passage at Doors
Verifying the clear passage width at standard hinged doors requires an understanding of exactly where to measure. The photo below shows that you measure horizontally from the face of...
-
Door Clear Width
Door Clear Width Open the door 90 degrees, measure from the face of the door to the edge of the door stop.
-
502.1 General
502.1 General. Car and van parking spaces shall comply with 502. Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from...
-
502.1 General
Car and van parking spaces shall comply with 502. Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline...